Need help?Do you have a question about the Omega CNI16D and is the answer not in the manual?
General| Model | CNI16D |
|---|---|
| Input Channels | 1 |
| Output Channels | 2 |
| Display | Dual 4-Digit LED |
| Number of Outputs | 2 |
| Operating Temperature | 0 to 50°C |
| Protection | IP65 Front Panel |
| Type | Controller |
| Communication Interface | RS-485 |
| Input Type | Thermocouple, RTD |
| Output Type | Relay |
| Control Mode | ON/OFF, PID |
| Output Current | 3A for Relay |
Details the functionality of the iSeries device as a monitor or controller.
Important safety and EMC information for installation and operation. Read this manual.
Instructions for inspecting shipment, customer service, manuals, and basic operations.
Details the front panel display and annunciators for various iSeries models.
Diagrams and descriptions for connecting power, outputs, inputs, and communication options.
Covers electrical installation, including power connections, fuses, and wiring considerations.
Instructions for connecting main power, including AC, DC, and low voltage options.
Wiring hookup for thermocouple input types and TC wire color chart.
Wiring hookup for RTD inputs, explaining two, three, and four-wire connections.
Wiring hookup for Process Current 0-20 mA input with internal/external excitation.
Wiring hookup for Process Voltage 0-100 mV, 0-1 V, 0-10 V inputs.
Details wiring for mechanical relay, SSR, pulse, and analog outputs.
Details RS-232 and RS-485 output connections for serial communication.
Information on the device's excitation output, noting limitations with certain options.
Explains the use and wiring of snubber circuits to protect relay contacts.
Instructions for setting the display color for dual display models using jumpers.
Introduces Run Mode and Menu Configuration Mode for operating the controller.
Steps for turning the controller on for the first time and its initial behavior.
Explains the requirement to use Standby Mode for configuration changes.
Flowchart illustrating the process for configuring ID and Setpoint parameters.
Guides on enabling, disabling, or changing the ID code for security levels.
Instructions for setting and adjusting Setpoint 1 and Setpoint 2 values.
Overview of the main configuration menu items and navigation flow.
Flowchart for selecting the input type: Thermocouple, RTD, or Process.
Steps to select and configure thermocouple input types and subtypes.
Steps to select RTD type, RTD value, and wire configuration.
Steps to select process input types: voltage, current, or mA.
Flowchart for configuring decimal point, temperature unit, and filter.
Details scale and offset configuration for process inputs like 4-20 mA.
Guides on enabling/disabling, setting modes, and values for Alarm 1.
Covers Enable/Disable, Absolute/Deviation, Latch/Unlatch, Contact Closure, Active modes.
Setting Power-on, Low, and High limit values for Alarm 1.
Guides on configuring Analog Output as retransmission or control outputs.
Covers Enable/Disable, Current/Voltage, Reading, and Output value settings.
Guides on enabling/disabling, setting modes, and values for Alarm 2.
Configure Loop Break Time and Thermocouple Field Calibration.
Settings for Setpoint Deviation and calibration logic.
Guides on configuring Output 1 for Self, Analog, ON/OFF, or PID control.
Selection of Control Type, Action Type, PID, and Auto Tune for Output 1.
Guides on configuring Output 2 for ON/OFF or PID control.
Selection of Control Type, Action Type, PID, and Auto Tune for Output 2.
Configure Ramp and Soak functions, including enable/disable and time values.
Configure ID codes for security and access control, including levels and changes.
Configure serial communication parameters like baud rate, parity, data bits, and protocol.
Select display colors for Normal, Alarm 1, and Alarm 2 states.
Covers accuracy, resolution, stability, A/D conversion, display, and input types.
Details supported input types: Thermocouple, RTD, Voltage, Current, and their properties.
Details control modes, outputs (Relay, SSR, Analog), and communication options.
Lists default factory preset values for various menu items and configurations.
Details CE approvals, electrical safety, overvoltage surge, and EMC compliance.
To Next Page
