Omega ILD24-UTP - Buttons Functions in Configuration Mode 3.2 Menu Configuration; Figure 3.1 Flow Chart for ID and Setpoints

72 pages

To Next Page

To Previous Page

3.2 Menu Configuration

It is recommended that you put the controller in the Standby Mode for

any configuration change other than Setpoints & Alarms.

Figure 3.1 Flow Chart for ID and Setpoints

Main Page

Table of Contents3
Part 1: Introduction6
1.1 Description6
1.2 Safety Considerations7
1.3 before You Begin8
Part 2: Setup9
2.1 Mounting9
Figure 2.1 Mounting9
Table 2.1 Front Panel Annunciators10
2.2 Rear Panel Connections11
Figure 2.2 Rear Panel Power and Output Connector Labels11
Figure 2.3 Rear Panel Input Connector Labels11
Table 2.2 Rear Panel Connector11
2.3 Electrical Installation12
2.3.1 Power Connections12
Figure 2.4 Main Power Connections12
Figure 2.5 Inside Cover Rear View12
Thermocouple - Input Connection13
Figure 2.6 Thermocouple Wiring Hookup13
Table 2.3 TC Wire Color Chart13
Two / Three / Four Wire RTD-Hookups14
Figure 2.7 Two/Three/Four-Wire RTD A) RTD-1000 Ohm and 500 Ohm Wiring Hookup14
B) RTD-100 Ohm Wiring Hookup14
Process Current - Wiring Hookup15
Process Voltage - Wiring Hookup15
Figure 2.8 Process Current Wiring Hookup15
(Internal and External Excitation)15
Figure 2.9 Process Voltage Wiring Hookup A) Without Sensor Excitation15
B) with Sensor Excitation15
Wiring Outputs - Wiring Hookup16
Figure 2.10 Output Connections: A) Mechanical Relay and SSR Outputs - Wiring Hook up16
B) Pulse and Analog Outputs - Wiring Hook up16
Figure 2.11 Communication Output: A) RS-232 Output - Wiring Hook up16
B) RS-485 Output - Wiring Hook up16
Figure 2.12 Excitation Output17
Figure 2.13 Snubber Circuits Wiring Hookup17
Part 3: Operation: Configuration Mode18
Introduction18
Table 3.1 Button Function in Configuration Mode18
Buttons Functions in Configuration Mode 3.2 Menu Configuration19
Figure 3.1 Flow Chart for ID and Setpoints19
ID Number20
Setpoints21
Configuration Menu22
3.2.4 Input Type Menu22
Figure 3.2 Flow Chart for Configuration Menu22
Figure 3.3 Flow Chart for Input Type Menu22
Input Type (Thermocouple)23
Input Type (RTD)24
Input Type (Process)25
Reading Configuration Menu25
Figure 3.4 Flow Chart for Reading Configuration25
Table 3.2 Conversion Table28
Alarm 1 Menu29
Figure 3.5 Flow Chart for Alarm 129
Analog Output (Retransmission) Menu33
Figure 3.6 Flow Chart for Analog Output (Retransmission)33
Alarm 2 Menu36
Figure 3.7 Flow Chart for Alarm 236
Loop Break Time Menu / Field Calibration37
Figure 3.8 Flow Chart for Loop Break Time / Field Calibration37
Output 1 Menu40
Figure 3.9 Flow Chart for Output 140
Output 2 Menu47
Figure 3.10 Flow Chart for Output 247
Ramp and Soak Menu50
Figure 3.11 Flow Chart for Ramp and Soak50
ID Code Menu52
Figure 3.12 Flow Chart for ID Code52
Communication (Options) Menu54
Figure 3.13 Flow Chart for Communication Option54
Display Color Selection Menu60
Figure 3.14 Flow Chart for Display Color Selection60
Part 4: Specifications63
Table 4.1 Input Properties65
Part 5: Factory Preset Values66
Table 5.1 Factory Preset Values66
Approval Information69

Omega ILD24-UTP - Buttons Functions in Configuration Mode 3.2 Menu Configuration; Figure 3.1 Flow Chart for ID and Setpoints

Table of Contents