15
Operating Instructions
Turning on the Appliance
Starting a cycle wash:
1 Draw out the lower and upper basket, load the dishes and push them back. It is commended to
load the lower basket first, then the upper one.
2 Pour in the detergent.
3 Insert the plug into the socket. The power supply is 220-240 VAC /50 HZ, the specification of the
socket is 10A 250VAC. Make sure that the water supply is turned on to full pressure.
4 Close the door, press the On/Off button to switch on the machine.
5 Press the program button, the wash program will be changed as following direction:
Normal->90min->Rapid->Pre-wash->Intensive->Heavy
If a program is selected, the responding light will be on. Then press the Start/Pause button, the dishwasher
begins to start.
Changing the Program
A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the
detergent may have already been released, and the appliance may have already drained the wash water. In
this case, the detergent dispenser must be refilled.
Press the Start/Pause button, the machine will be in standby state, press the program button more than 3s
then you can change the program to the desired cycle setting.
NOTE: If you open the door during a wash cycle, the machine will pause. After you close the door, the
machine will keep on working after 10 seconds.
Forgot to Add a Dish
A forgotten dish can be added any time before the detergent cup opens:
1. Press the Start/Pause Button to stop the
washing.
2. Open the door a little.
3. After the spray arms stop spinning, you can open
the door completely.
4. Add forgotten dishes.
5. Close the door
6. Press the Start/Pause Button, the dishwasher will
run after 10 seconds.
At the End of the Wash Cycle
When the working cycle has finished, the buzzer of the dishwasher will sound for 8 seconds, then stop. Turn off the
appliance using the ON/OFF button, shut off the water supply and open the door of the dishwasher. Wait for a few
minutes before unloading the dishwasher to avoid scald the dishes and utensils are still hot and more susceptible to
breakage. They will also dry better.
Switch Off the Dishwasher
The Led screen is on but the colon icon is not blinking, only in this case the programme has ended.
1. Switch off the dishwasher by pressing the ON/OFF button.
2. Turn off the water tap.
Open the door carefully.
Hot dishes are sensitive to knocks. The dishes should be allowed to cool down around 15 minutes before removing
from the appliance.
Open the dishwasher's door, leave it ajar and wait a few minutes before removing the dishes. In this way they will be
cooler and the drying will be improved.
Unloading the dishwasher
It is normal that the dishwasher is wet inside.
Empty the lower basket first and then the upper one. This will avoid water dripping from the upper Basket onto the
dishes in the lower one.
Warning: It is dangerous to open the door whilst washing. Hot water may scald you.
16
Maintenance and Cleaning
Filtering System
The filter prevents larger remnants of food or other objects from getting inside the pump. The residues may
block the filter, in this case they must be removed.
The filter system consists of a coarse filter, a flat (Main filter) and a
microfilter(Fine filter).
Main filter 1
Food and soil particles trapped in this filter are pulverized by a special jet on
the lower spray arm and washed down to drain.
Coarse filter 2
Larger items, such as pieces of bones or glass, that could block the drain are
trapped in the coarse filter. To remove the items caught by this filter, gently
squeeze the tap on the top of this filter and lift it out.
Fine filter 3
This filter holds soil and food residues in the sump area and prevents it from
being redeposit on the dishes during wash cycle.
Filter Assembly
The filter efficiently removes food particles from the wash water, allowing it to be recycled during the cycle.
For best performance and results, the filter must be cleaned regularly. For this reason, it is a good idea to
remove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter
and cup under running water. To remove the filter device, pull the cup handle in the upward direction.
Warning: The dishwasher must never be used without the filters. Improper replacement of the filter may
reduce the performance level of the appliance and damage dishes and utensils.
Turn the filter in an anti-clockwise direction.
Lift the filter assembly up.
Note: Reverse the above procedure to install the filter system.
• Inspect the filters for blocking after every time the dishwasher has been used.
• By unscrewing the coarse filter, you can remove the filter system. Remove any food remnants and
clean the filters under running water.
• The entire filter assembly should be cleaned once a week.
To Next Page
Loading...
