Omega OM-CP-IFC200 - User Manual

Package Contents
Set up USB Datalogger Interface
IMPORTANT: Do not connect the OM-CP-IFC200 to
your PC until instructed to do so or the setup will not
work.
A Insert the OM-CP Data Logging
Software CD-ROM into your CD-
ROM drive. The CD should run
automatically, and the CD
Contents screen should appear. If
it does not, click the Start button
and choose Run. In the field that
appears, enter D:\autorun.exe
(If “D” is the letter of your CD-
ROM drive).
B Click on the Install Omega
2.00.63 or later link on the CD
Contents screen to start the install
of the Data Recorder Software. A
new window will appear. Follow
the on screen prompts to complete
the software installation. See the
Software Manual or visit us online
at www.omega.com additional
information.
C To install the OM-CP-IFC200, click
the Install USB Interface
Drivers link on the CD Contents
screen. A new window will appear
prompting for a directory and to
start the installation.
If you choose to change the
directory where the drivers will be
stored, do so here by clicking
Browse. When the directory is
set to the correct location, click the
Install button to start the
installation.
D When using Windows XP, a screen
may appear indicating the software
has not passed Windows
® Logo
Testing. This software has been
tested and works properly with
Windows XP. Click the Continue
A
B
C
Anyway button to resume with the
installation. When finished, a
message will display indicating that
the installation was successful.
All the necessary drivers for the
OM-CP-IFC200 to work correctly
should now be pre-installed onto
your PC. Click the OK button to
close the Pre-Installer window. In
the CD Contents window, click the
Exit CD Browser link to exit the
autorun program.
D
Model No. OM-CP-IFC200
For Win 2000/XP
B
B
B
A Remove the warning label to
expose the USB connector.
Connect one end of the
included USB cable to the USB
port of the OM-CP-IFC200.
For Windows XP
D
For Windows 2000
A Remove the warning label to
expose the USB connector.
Connect one end of the included
USB cable to the USB port of
the OM-CP-IFC200.
B Connect the other end to a USB
port on your PC. When the
OM-CP-IFC200 is plugged in,
the Found New Hardware
window will display. Windows
2000 will automatically install
the proper software drivers for
the OM-CP-IFC200 as long as
step one was completed.
Allow the PC to complete the
installation. Once finished, the
Found New Hardware window
will disappear and the blue
Power LED on the OM-CP-
IFC200 will light up. Once this
occurs, you can skip ahead to
step three, Test USB Datalogger
Warning:
Install driver before
Connecting this device.
A
1
Connect the USB Datalogger Interface
2
Warning:
Install driver before
Connecting this device.
A
USB Datalogger Interface
Quick Installation Guide
• USB Interface Device
• USB Cable
• 3.5mm Audio cable
• Data Recorder Software
CD-ROM
• Quick Installation Guide

Summary

Set up USB Datalogger Interface

Install Data Recorder Software

Install the Data Recorder Software by clicking the Omega 2.00.63 link on the CD.

Install USB Interface Drivers

Click the Install USB Interface Drivers link to begin the driver installation process.

Handle Windows XP Logo Testing Warning

Acknowledge Windows XP logo testing warnings; the software is tested and works.

Connect the USB Datalogger Interface

Connect USB Cable to Device and PC

Remove the warning label, connect the USB cable to the device and then to the PC.

Automatic Driver Installation

Allow Windows to automatically install software drivers for the Found New Hardware.

Handle Windows XP Logo Warning

Continue installation if Windows XP indicates software has not passed logo testing.

Select Communication Port

From the Communication menu, select the appropriate USB port (e.g., USB1).

Set Communication Baud Rate

Configure the baud rate in the software to match the connected datalogger.

Test USB Datalogger Interface Operation

Verify Device Recognition

Ensure the OM-CP Data Logging Software recognizes the connected device.

Configure Baud Rate for Dataloggers

Set the software baud rate to match the specific OM-CP Datalogger being used.

Omega OM-CP-IFC200 Specifications

General

Connection Type	USB
Series	OM-CP
Compatibility	OM-CP-PROCESS101A, OM-CP-QUADTEMP, OM-CP-OCTTEMP, OM-CP-VOLT101A, OM-CP-CURRENT101A, OM-CP-HUMIDTP101A, OM-CP-TC101A
Interface	USB
Cable Length	1.5 m
Connector	USB
Material	Plastic
Probe Type	Not applicable