Index-3
Index
Index
R Page
range type ........................................................................... 1-2
rear panel ............................................................................ 3-3
recorder ............................................................................... 1-1
recording ........................................................................... 1-13
recording (computation channels) ..................................... 1-25
recording color ...................................... 1-14, 7-8, 7-11, 9-23
recording span .................................................................... 1-2
recording start printout ...................................................... 1-19
recording zone .......................................................... 6-4, 9-15
reference junction compensation ........................................ 1-4
reference pen .................................................................... 1-15
reference time ................................................................... 7-14
reflash alarm ............................................................. 1-10, 7-3
registering display types to screens .................................... 8-3
relational computation ............................................... 1-24, 9-6
relative time mode ............................................................. 9-21
relay contact input ............................................................. 2-11
relay contact output ........................................................... 2-11
relay numbers ......................................................... 5-11, 9-12
releasing the alarm output ................................................ 3-18
releasing the key lock ....................................................... 3-19
remaining chart length ...................................................... 11-1
remote control ......................................................... 1-28, 7-28
remote control input terminals ........................................... 2-10
remote signal .................................................................... 1-29
replacement period for expendable parts ......................... 11-9
replacing felt pens ............................................................... 3-7
replacing the internal light LED ......................................... 11-3
replacing the plotter pen ..................................................... 3-8
report data ............................................................... 7-14, 9-26
report mode .................................................................... App-2
resetting the computed values ............................................ 9-1
resetting the report data .................................................... 3-17
resetting the TLOG computed value ................................. 9-22
revisions .................................................................................. i
ribbon cassette .................................................................. 3-10
ribbon feeding knob .......................................................... 3-10
ribbon is loose ................................................................... 3-10
RJC ..................................................................................... 7-7
RTD ..................................................................................... 5-2
run modes ........................................................................... 4-1
S Page
safety precautions ................................................................. iii
safety standards .................................................................... iii
safety symbols ...................................................................... iii
scale printout .................................................................. App-2
scaling ................................................................................. 1-3
scan interval ........................................................................ 1-2
secondary chart speed ........................................................ 6-9
Setting complete screen ..................................................... 4-3
setting mode ....................................................................... 4-1
settings necessary to use various functions ..................... 4-13
Setup ................................................................................. 3-14
setup guide ....................................................................... 4-13
setup items (basic setting mode) ...................................... 4-10
setup Items (setting mode) ................................................. 4-9
shunt resistor ...................................................................... 1-2
skip ...................................................................................... 5-8
sprocket teeth ..................................................................... 3-5
square root ........................................................................ 1-24
square root computation ............................................. 1-3, 5-7
square root low-cut function .............................................. 7-24
standard accessories ............................................................ vi
standard performance ..................................................... 12-19
standard temperature device ............................................ 11-5
start recording ................................................................... 3-11
starting the computation ...................................................... 9-1
status display .................................................................... 1-22
status of the remote control input terminal .......................... 9-5
stop recording ................................................................... 3-11
stoppers ...................................................................... 3-4, 3-6
stopping the computation .................................................... 9-1
suffix code .............................................................................. v
SUM scale ..................................................... 7-14, 9-14, 9-26
supported standards ....................................................... 12-18
switching the display screen ............................................. 3-12
T Page
tag ................................................................... 6-7, 7-11, 9-18
TC ....................................................................................... 5-2
temperature unit ................................................................ 7-31
thermocouple ...................................................................... 5-2
thermocouple input ............................................................. 2-6
time constant ....................................................................... 6-2
time printout format ................................................. 1-18, 7-26
time tick ................................................................ 1-16, App-1
time tick cancel mark ........................................... 1-16, App-1
timer .................................................................................. 9-21
TLOG computation .................................................... 1-24, 9-8
transistor input .................................................................. 2-11
trend recording ...................................... 1-14, 6-6, 9-17, 12-4
trend recording interval ....................................................... 6-1
trigger ................................................................................ 1-29
troubleshooting ................................................................. 10-4
type of measured values ................................................... 7-14
type of report data ............................................................. 9-26
types of computations ....................................................... 1-24
types of inputs ..................................................................... 1-2
U Page
unit ............................................................................ 5-12, 9-9
unit in computations .......................................................... 1-25
V Page
VFD ................................................................................... 1-22
Volt ...................................................................................... 5-2
W Page
wiring (measuring input ) ..................................................... 2-8
wiring (optional terminal) ..................................................... 2-9
wiring (power supply) ........................................................ 2-12
Z Page
zone recording .................................................................. 1-14
Index
To Next Page
Loading...