OMP Versa - User Manual

1
7
5
4
4
4
4
8
2
10
6
9
3
Move or Rotate the Clamping Assembly:
1. Remove the bow and loosen the Tightening Knob (7) almost all the way.
2. Remove the Tightening Knob Shoulder Screw (8) with the 1/8" hex wrench (provided)
while holding the Tightening Knob steady with the other hand.
3. Remove the clamping assembly including the Guide Plate (6) and move the Tightening
Knob Shoulder Screw into the other hole (or rotate it), making sure that the Shoulder
Screw goes in all the way (the head of the screw will be approximately even with the
surface of the Main Beam (1).
4. Move the clamp assembly to the new position and, using the long end of the 1/8" hex
wrench through the hole in the C-Frame, thread the Shoulder Screw into the Tighten-
ing Knob while also positioning the Guide Plate between the four Cushioning Pads (4)
and against the frame.
5. Firmly re-tighten the Tightening Knob Shoulder Screw with the short arm of the hex
wrench in the head of the Shoulder Screw.
Adjust the OMP Versa-Cradle Bow Vise Ball Assembly:
If the Versa-Cradle’s handle over rotates against its stop without fully tightening
the ball, loosen the handle as far as it will go, loosen the set screw (Image 1) directly
above the handle half a turn with the 3/32” hex wrench (provided) insert the short
end of the hex wrench into one of the seven holes (Image 2) on the bottom side of the
tightening nut and rotate it in a counterclockwise direction until snug as viewed from
the top side of the Versa-Cradle. Working the handle back and forth a little during this
process can help free the nut and rotate it. Once almost all of the slack is taken out of
the handle, retighten the set screw.
1
2
3
4
5
6
7
8
9
10
Main Beam
Main Beam Screws
(4, 10-32 x 7/8" Button Head Screws)
Base Screws
(4, 10-32 x 3/4" Button Head Screws)
Cushioning Pads
C-Frame
Guide Plate
Tightening Knob Shoulder Screw
Shoulder Screw
Base Plate
Wood Screws
Beam Assembly
3
1
2
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
Case Assembly
Case (CNC Machined Steel Case)
Ball (CNC Machined ball with beam post)
Handle (Steel handle w/ welded threaded post)
Brass Socket (CNC Machined brass ball socket)
Clamping Nut (Adjustable)
Case Set Screw (1, 10-32 x 3/8” Set Screw)
Base (Aluminum machined base for case)
Base Screws (4, 10-32 x 3/4” Flat Screws)
Retaining Ring (1, 1-1/2” Internal Retaining Ring)
Ball Tension Spring
Image 1
Set Screw
Image 2
Ball Tension Spring (10) keeps a constant light tension on the
Handle (3). The Ball Tension Spring can be removed by rotating
the Handle all the way to the tight position, compress the spring
together and pull the spring out. Re-installation is done in reverse.
Ball Tension Spring
Versa-Cradle Bow Vise
Assembly Instructions

Summary

Versa-Cradle Bow Vise Assembly

Move or Rotate Clamping Assembly

Instructions for moving the clamping assembly by removing and re-inserting the Tightening Knob Shoulder Screw.

Adjust Ball Assembly for Full Tightening

Procedure to adjust the Versa-Cradle's ball assembly to prevent handle over-rotation.

Ball Tension Spring Function

Explanation of the Ball Tension Spring's role in maintaining handle tension and its removal/re-installation.

Wide Limb Adapter Assembly

Remove Narrow Limb Clamp Assembly

Steps to remove the narrow limb clamp assembly using the Shoulder Screw and 1/8" hex wrench.

Install Wide Limb Adapter

Procedure for aligning and fastening the Main Beam, Guide Plate, and Mounting Plate for the wide limb adapter.

Mounting the Bow Vise

Instructions on how to mount the Versa-Cradle Bow Vise using screws or bolts.

Mounting the Bow

Guide on how to securely clamp a bow limb into the vise using the Tightening Knob.

Overview

1. Function Description
2. Standard Versa-Cradle Bow Vise
3. Versa-Cradle Wide Limb Adapter
4. Important Technical Specifications (Derived from diagrams and text)
5. Usage Features
6. Maintenance Features

The October Mountain Products Versa-Cradle Bow Vise is a versatile tool designed for securely holding bows during maintenance, tuning, or other tasks. It comes in two primary configurations: the standard Versa-Cradle Bow Vise and the Versa-Cradle Wide Limb Adapter, catering to different bow types, including crossbows and vertical bows.

Function Description:

The core function of the Versa-Cradle Bow Vise is to provide a stable and adjustable platform for holding a bow. It achieves this through a clamping assembly that grips the bow limb and a ball-and-socket mechanism that allows for multi-directional positioning. The device can be mounted to a workbench or other secure surface using wood screws or bolts.

Standard Versa-Cradle Bow Vise:

This configuration is suitable for most standard bow limbs.

• Clamping Assembly: The clamping assembly consists of a C-Frame (5), Guide Plate (6), Tightening Knob (7), Shoulder Screw (8), and Cushioning Pads (4). The bow limb is placed between the opposing Cushioning Pads, and the Tightening Knob is tightened to secure it.
• Adjustability: The clamping assembly can be moved or rotated along the Main Beam (1) to accommodate different bow sizes and shapes. This involves loosening and re-tightening the Tightening Knob Shoulder Screw (7) and Shoulder Screw (8) using a 1/8" hex wrench.
• Positioning: The bow's position is further adjusted by a ball-and-socket mechanism. This includes a Ball (2) with a beam post, a Handle (3) with a welded threaded post, a Brass Socket (4), and a Clamping Nut (5). Loosening the Handle allows the bow to be moved to almost any position, while tightening it locks the ball in place.
• Mounting: The entire vise assembly is mounted to a surface via a Base Plate (9) and Wood Screws (10).

Versa-Cradle Wide Limb Adapter:

This adapter is designed specifically for bows with wider limbs, such as many crossbows. It replaces the standard narrow limb clamp assembly.

• Installation: To install the Wide Limb Adapter, the narrow limb clamp assembly is first removed. This involves accessing and removing the Shoulder Screw (8) from the C-Bracket, then removing the entire clamp assembly from the Main Beam (1). The limb pads are also removed from the Main Beam. The Wide Limb Adapter components, including the Guide Plate (3) and Mounting Plate (6), are then aligned with the Main Beam (1) and fastened together using two 10-32 x 5/8 countersunk screws (9). The C-Frame assembly (5) is then slid into place and aligned with the adapter's guide cutout, and the Shoulder Screw (8) is inserted and tightened.
• Clamping: Similar to the standard vise, the Wide Limb Adapter uses Cushioning Pads (4) to grip the wider bow limb. The Tightening Knob (7) is used to secure the limb.

Important Technical Specifications (Derived from diagrams and text):

• Screws:
  • Main Beam Screws: 4, 10-32 x 7/8" Button Head Screws
  • Base Screws: 4, 10-32 x 3/4" Button Head Screws (for Beam Assembly)
  • Base Screws: 4, 10-32 x 3/4" Flat Screws (for Case Assembly)
  • Case Set Screw: 1, 10-32 x 3/8" Set Screw
  • Wide Limb Adapter Fasteners: 2, 10-32 x 5/8" (for Guide Plate, Main Beam, Mounting Plate)
  • Wide Limb Adapter Countersunk Screws: 2, 10-32 x 5/8"
  • Wood Screws: 10 (for mounting base plate)
• Hex Wrenches: A 1/8" hex wrench is provided for adjusting the clamping assembly, and a 3/32" hex wrench is provided for adjusting the ball tension.
• Materials (indicated by part names):
  • Main Beam: Likely a robust metal.
  • Case: CNC Machined Steel.
  • Ball: CNC Machined with beam post.
  • Handle: Steel with welded threaded post.
  • Brass Socket: CNC Machined Brass.
  • Base (for Case Assembly): Aluminum machined.
  • Cushioning Pads: Likely a soft, non-marring material.

Usage Features:

• Secure Bow Holding: The clamping mechanism, with its cushioning pads, is designed to firmly hold bow limbs without causing damage.
• Multi-directional Adjustment: The ball-and-socket joint allows for a wide range of motion, enabling users to position the bow at virtually any angle for optimal access during work.
• Easy Bow Mounting: To mount a bow, simply loosen the Tightening Knob, slide a limb between the cushioning pads, ensure it's centered and straight, and then tighten the knob firmly.
• Interchangeable Clamping Assemblies: The ability to switch between the standard narrow limb clamp and the wide limb adapter makes the vise adaptable to various bow types.
• Bench Mounting: The vise can be securely mounted to a workbench using the provided wood screws or bolts, ensuring stability during use. The manual suggests using leather or rubber under the base to protect fine benches.

Maintenance Features:

• Adjusting Ball Tension: If the handle over-rotates or the ball doesn't tighten properly, the ball tension can be adjusted. This involves loosening the handle, then loosening the set screw (Image 1) above the handle by half a turn using the 3/32" hex wrench. The tightening nut can then be rotated counterclockwise (as viewed from the top) using the short end of the hex wrench inserted into one of the seven holes (Image 2) on its bottom side until snug. Working the handle back and forth can help free the nut. Once slack is removed, the set screw is re-tightened.
• Ball Tension Spring (10): This spring maintains a constant light tension on the Handle (3). It can be removed for maintenance or replacement by rotating the Handle to the tight position, compressing the spring, and pulling it out. Re-installation is the reverse process.
• Smooth Operation: After installing the Wide Limb Adapter, it's recommended to test the unit for smoothness of operation to ensure there are no catch points. This implies that regular checks for smooth movement are part of maintaining the vise.
• Hex Wrench Included: The provision of hex wrenches (1/8" and 3/32") with the product indicates that users are equipped for basic adjustments and maintenance.

The Versa-Cradle Bow Vise is a robust and adaptable tool, designed for both ease of use and long-term durability, with features that allow for precise positioning and straightforward maintenance.

OMP Versa Specifications

General

Brand	OMP
Model	Versa
Category	Racks & Stands
Language	English