EasyManua.ls Logo

Oneida Air Systems Dust Deputy Low-Pro Plus - User Manual

Default Icon
8 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Rev: B 20230928LL Doc. # ZBM000053
English
Appearance may vary slightly
Dust Deputy Low-Pro
Lid Separator
Plus
# AXD259911
Patents: www.oneida-air.com/patents
Start-Up Information
1. DO NOT use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
2. DO NOT collect ammable or combustible liquids, gases, or explosive dusts, such as gasoline or other fuels, lighter uid, cleaners, oil-based paints, natural gas,
hydrogen, coal dust, magnesium dust, grain dust, aluminum dust, sugar dust, our dust or gun powder.
3. Can be used for collecting non-ammable liquids.
4. DO NOT use or store near hazardous materials.
5. DO NOT operate in areas where explosion risks are high. Areas of high risk include, but are not limited to, areas near pilot lights, open ames, or other ignition
sources.
6. ALWAYS wear a NIOSH approved respirator when emptying dust bins and during operation. Dust created by machinery operations may cause cancer, birth defects,
or long-term respiratory damage. Be aware of dust hazards associated with each work piece material.
7. NEVER introduce sparks or sources of ignition.
8. ENSURE all equipment and connections are electrically grounded.
9. ONLY operate in locations that has a re extinguisher available nearby.
10. ALWAYS dispose of waste in a re safe area aer each use. NEVER leave wood dust in a building or vehicle. Wood dust mixtures are highly ammable and can be
explosive.
READ THE SAFETY PRACTICES, INSTALLATION AND MAINTENANCE INSTRUCTIONS, AND YOUR WET/DRY
VACUUMS OWNER’S MANUAL BEFORE ASSEMBLING AND USING THE DUST DEPUTY.
SOME DUSTS ARE HIGHLY FLAMMABLE OR EXPLOSIVE. LEARN/ KNOW WHAT YOU ARE DEALING WITH. FOLLOW
ALL LOCAL, STATE, FEDERAL & NFPA CODES AND GUIDELINES.
18-1/2"
470 mm
5-1/16"
129 mm
3-13/16"
98 mm
Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.
12-3/8"
315 mm
As installed on a
5 Gallons
19 Liters
Bucket
Dimensions

Questions and Answers

  • K
    Katelyn HerreraJul 30, 2025
    Why is the hose pulling off my Oneida Air Systems Water Filtration Systems?
    • D
      Darin CastilloJul 30, 2025
      If the hose keeps pulling off from your Oneida Air Systems Water Filtration Systems, it's likely due to loose hose connections. Here's what you can do: 1. Use flexible couplers if you have varied hose diameters. These are available at local hardware stores. 2. Secure the connection with a hose clamp. 3. Increase friction by wrapping the inlet and outlet of the Low-Pro with electrical tape. 4. For a more permanent solution, use a sheet metal screw to secure the hose.
  • M
    Michael TorresAug 5, 2025
    How to fix low air volume in Oneida Air Systems Water Filtration Systems?
    • T
      Tina RomeroAug 5, 2025
      Low air volume in your Oneida Air Systems Water Filtration Systems is often caused by a clog in the system. To fix this: 1. Clean the vacuum and its filter according to the manufacturer's specifications. 2. Inspect all hose connections for any blockages inside the hose.
  • D
    Diana SmithAug 11, 2025
    What to do if the drum is collapsing on my Oneida Air Systems Dust Deputy Low-Pro Plus?
    • J
      Joel MacdonaldAug 11, 2025
      If your Oneida Air Systems Water Filtration Systems drum is collapsing, it's likely due to blocked airflow. Make sure the end of the hose isn't blocked to resolve this issue.
  • T
    Timothy MooreAug 17, 2025
    Why is my Oneida Air Systems Dust Deputy Low-Pro Plus Water Filtration Systems not separating well?
    • E
      elopezAug 17, 2025
      If your Oneida Air Systems Water Filtration Systems isn't separating dust well (with more than just a tiny amount reaching the vacuum), it's probably due to air leaks in the bucket. Check for leaks between the Low-Pro Lid Separator and the bucket, and also inspect the bucket for any holes or leaks.
  • A
    Ariel NelsonAug 22, 2025
    What to do if material is not dropping into the dust container of my Oneida Air Systems Dust Deputy Low-Pro Plus Water Filtration Systems?
    • V
      vaughnpaulAug 22, 2025
      If material isn't dropping into the dust container of your Oneida Air Systems Water Filtration Systems, it might be because you're collecting large, bulky material. This type of material can swirl around. Try restarting the system or temporarily cutting off airflow to help the material drop down.

Summary

Start-Up and Safety Information

Safety Precautions

Key safety practices for operation, including fire hazards, material handling, and PPE.

Product Dimensions

Physical measurements of the Dust Deputy Low-Pro Lid Separator.

System Contents and Assembly

Component List and Initial Assembly

Lists included parts and covers initial assembly steps like gasket and latch attachment.

Assembly and Grounding

Connecting Hoses and Vacuum

Instructions for connecting the dust separator to vacuum and tool hoses.

Optional Grounding Instructions

Procedure for installing metal tape and wire for grounding in sensitive applications.

Troubleshooting and Support

Troubleshooting Common Issues

Solutions for problems like poor separation, low air volume, and hose connection issues.

Warranty and Customer Support

Details warranty period, return policy, and customer service contact information.

Oneida Air Systems Dust Deputy Low-Pro Plus Specifications

General IconGeneral
BrandOneida Air Systems
ModelDust Deputy Low-Pro Plus
CategoryWater Filtration Systems
LanguageEnglish

Related product manuals