S機種 メインマイコン(M3062LFHPFP)
38 P60/~CTS0/~RTS0
~
I L Tuner FM stereo detection terminal /Tuner PLL serial data entry terminal
39 P57/~RDY/CLKOUT FREQCAL O CLK Clock output terminal for adjustment
40 P56/ALE ~SD I L Tuner recovery detection terminal
41 P55/~HOLD ~FEPM O H Port for Flash transfer
42 P54/~HLDA SUBREQ I H Communication ready signal input terminal from sub micro-computer
43 P53/BCLK I Unused terminal
44 P52/~RD I Unused terminal
45 P51/~WRH/~BHE I Unused terminal
46 P50/~WRL/~WR ~FCE I H Port for Flash transfer
47 P47/~CS3 DIRCLK O CLK DIR serial communication clock output terminal.
48 P46/~CS2 DIRSI I H DIR serial communication data entry terminal.
49 P45/~CS1 DIRSO O H DIR serial communication data output terminal.
50 P44/~CS0 DIRCS O H DIR tip/chip selection output terminal.
51 P43/A19 SELCLK O H Function switch (R2S15211) serial clock output terminal
52 P42/A18 SELDAT O H Function switch (R2S15211) serial data output terminal
53 P41/A17 I H Unused terminal (GND)
54 P40/A16 TUMUT O H Tuner mute output terminal < At the time of WAIT/ power failure input port >
55 P37/A15 ~CDAMUTE O L CD analog mute output terminal.
56 P36/A14 ~MUTCTRL O L MUT control output terminal.
57 P35/A13 ~CDDACMUT O L Mute signal output terminal to outside DAC.
58 P34/A12 ~AMUT O L AMUTE control output terminal.
59 P33/A11 USB_RST O L USB tip/chip reset terminal
60 P32/A10 RCPOW O H Circuit power source control terminal around receiver
61 P31/A09 ACPOW O H Power source (Main trance) control terminal
62 VCC2 Vcc2 Vcc2
63 P30/A8(/-/D7) USB_MUSHNG O USB tip/chip MUCHNG terminal
64 VSS Vss Power source GND
65 P27/AN27/A7(/D7/D6) USB_BUSY O L USB tip/chip BUSY terminal
66 P26/AN26/A6(/D6/D5) USB_SCL O CLK USB tip/chip clock terminal
67 P25/AN25/A5(/D5/D4) USB_SDA I/O USB tip/chip data terminal
68 P24/AN24/A4(/D4/D3) E2PROM_SDA I/O H E2PROM serial data terminal
69 P23/AN23/A3(/D3/D2) E2PROM_SCL O CLK E2PROM3 line serial clock output terminal.
70 P22/AN22/A2(/D2/D1) E2PROM_WP2 O L E2PROM write protection cancellation output terminal
71 P21/AN21/A1(/D1/D0) RDSENABLE I H With RDS effective/invalid change input terminal H validity
72 P20/AN20/A0(/D0/-) DABENABLE I H With DAB effective/invalid change input terminal H validity
73 P17/D15/~INT5 SYSIN I H RI input terminal < Only at the time of WAIT with UP interruption processing >
74 P16/D14/~INT4 ~RDSCLK I RDS serial clock input terminal/RDS there is no model GND
75 P15/D13/~INT3 CDSCORI
76 P14/D12 ~SYSOUT O L ~SYSOUT
77 P13/D11 PROTECT_I I H
After the relay ON of the electric current and the temperature protect detection terminal
ACPOWER starting protect detection operation from 0.5 seconds
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
To Next Page
Loading...
