Onkyo TX-830 - Remote Control Operations

211 Speaker Selector Switches (SPEAKERS) 29 80 Tape Operation Keys (DECK-A, DECK-B)
This unit can drive two pairs of speakers in pairs (A or B) or These keys control Onkyo double cassette tape decks that can
fours (A + B). To listen to both Speaker Systems at once, be remote controlled. Use the DECK-B keys to contral single
depress both Speaker Selector switches. cassette tape decks with the RI mark and cassette tape decks
22 Headphones Jack (PHONES) that do not have the (RI mark. . |
Stereo headphones with a standard binaural plug can be “Ai: When this is pressed, the recording stand-by mode is
connected here. entered.
< : The tape plays, moving from right to left, or, in the re-
23 Signal Strength Indicator cording stand-by mode, recording begins.
The optimum tuning point is achieved when the most indicators ™ =: Interrupts all operations.
are lit. >» :The tape plays, moving from left to right, or, in the re-
24 Stereo Indicator (STEREO) cording stand-by mode, recording begins.
This indicator lights when an FM stereo broadcast is «<=: Fast forward from right to left.
being received. It does not light when the FM MUTE/ p> = Fast forward from left to right.
Mode button [9] is in the OFF (MONO) position or when a For connections, please refer to the section “Connections for
weak FM stereo broadcast is being received. Remote Control.”
Consult your Onkyo service center for further details.
® Remote Control Transmitter Controls (RC-118S8) 81] CD Operation Keys (CD) .
These keys are used to operate an ONKYO CD player with the
NOTE: FRE mark. .
> : Press this key to play the CD player.
For the RC-AV10M transmitter provided with the . 11 +=: Press this key to pause the CD play back. To resume
TX-850M/830M, —please refer to the separate instruction ma- disc play, press the PLAY key.
nual (included). ™@ :Press this key to stop the CD player.
I¢¢ : Press this key to go back to the beginning of the current
25) Power Key ; oo. . track and again to skip back to the previous track.
When the TX-850/830 $ stand-by/received indicator is it, Pri: Press this key to skip to the next track.
pressing this key will turn on the TX-850/830 (the stand-by/
received indicator will go out). Pressing the key again will turn Refer to the CD player instruction manual for additional in-
off the TX-850/830 (the stand-by/received indicator will light). formation.
The remote control transmitter also has a switch that turns For connections, please see the section on “Connections for
power on and off to the AC outlets on the rear panel of the Remote Control.” |
TX-850/830. Consult your Onkyo service center for further details.
26 Sleep key and indicators 83 Audio Muting Key (AUDIO MUTING) and Indicator
Press to set the power off timer. The sleep timer is a function This key temporarily switches off the sound from the speaker or
which turns off the power to the system from the time it is set. headphone. Pressing this key will operate the TX-850/830's audio
When this key is pressed, “90 MIN” is displayed on the tuner’s muting circuit. The audio muting indicator will
display for 5 seconds, and the power goes off 90 minutes later. light. Pressing the key again will turn off the audio muting.
Each time the key is pressed during 5 seconds, the timer setting 83 Volume Keys ( A UP, ¥ DOWN)
changes , 60, and 30 minutes, in turn. While the sleep timer This key has the same function as that of the volume
is
operating,
the
indicator
is
lighted.
If
the
sleep
key
contro![15].
The
volume
level
can
be
adjusted
by
pressing
the
is pressed during this time, the amount of time remaining on UP or DOWN key, with the volume control knob rotating si-
the sleep timer is displayed, and if the key is pressed during muitaneously.
that display, 30 minutes will be subtracted from that time.
If the key is pressed until the display shows 0 minutes, the sleep Operations
timer is cancelled, and the power is not turned off. ne
Phono Operation Key (PLAY/REJECT)
This key ts used to operate the turntable. The phono operation Tuner Reception
key can be used only when the PHONO input selector key 1. Confirm that the TAPE-2 MONITOR indicator [2]is off, audio
has been pressed. Each time the phono operation key is muting is off, and press the FM or AM Input Selector button
pressed, the remote control transmitter alternately emits the (3).
play or reject command. Refer to the turntable instruction 2. To tune in an FM or AM station not stored in the memory, press
manual for additional instructions on operating the turntable. one of the Tuning selector buttons [7]. If you press UP, the
For connections, please refer to the section “Connections for frequency is increased. Pressing DOWN decreases. Note that
Remote Control.” the frequency is changed in 200kHz (or 50kHz) steps in FM
Consult your Onkyo service center for further detatis. and 10kHz (or 9kHz) steps in AM when the Tuning selector
button is pressed in single steps. If this button is pressed con-
NOTE: tinuously for more than 0.5 seconds, the auto tuning mode is
Before starting record piay using remote control, confirm that
there is a record on the platter. If there is no record, the stylus
entered, and frequencies are scanned automatically. When a
broadcast signal is received, scanning stops and that frequency
is displayed. lf a different frequency is desired, press the button
once again.
@ Scanning will not stop for broadcasts weak enough to be sup-
pressed by the muting circuit. To receive a weak FM broadcast,
set the FM Muting/Mode button [9] to the OFF position and
select the frequency of the desired broadcast station.
3. To recall a station stored in the memory, simply press the Preset
station button corresponding to the desired station.
Be sure to set the Shift button [8] to the range (1-10 or 11-20)
for the memory channel to be recalled. This is a random FM/AM
memory. {if a preset station button is pressed when the input
selector is not set to FM or AM, the input is automatically
switched to FM or AM.
will be lowered to the platter, resulting in serious damage to the
stylus.
28 Tuner Operation Keys ( « PRESET Pp )
When the UP ( » ) or DOWN ( € ) remote this key is pressed,
the next higher or lower memory channel is recalled. Each time
UP or DOWN key is pressed, the following memory channel
in the corresponding direction is recalled. If the key is held
down the memory channel will increase or decrease contin-
uously until key is released.