EasyManua.ls Logo

Onkyo TX-8210 Service Manual

Onkyo TX-8210
24 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image

Other manuals for Onkyo TX-8210

Question and Answer IconNeed help?

Do you have a question about the Onkyo TX-8210 and is the answer not in the manual?

Onkyo TX-8210 Specifications

General IconGeneral
Power Output50 W per channel (8 ohms, 20 Hz-20 kHz, 0.08% THD)
Number of Channels2
Frequency Response10 Hz-100 kHz (+1 dB, -3 dB)
Total Harmonic Distortion0.08%
Input Sensitivity (line)200 mV
Tuning rangeFM, MW
Input sensitivity (MM)2.5mV
Signal to noise ratio (line)106 dB
Speaker load impedance4 - 16 ohms
Signal-to-Noise Ratio106 dB

Summary

ONKYO SERVICE MANUAL

Safety-Related Component Warning

Critical components for fire and electric shock risk must be replaced with specified parts.

Specifications

Amplifier Section Specifications

Details power output, distortion, and input sensitivities for the amplifier.

Tuner Section Specifications

Details tuning range, sensitivity, and selectivity for FM and AM reception.

General Specifications

Covers power supply, dimensions, and weight of the unit.

Service Procedures

Replacing Fuses

Instructions for replacing fuses, including type and rating.

Initializing the Unit

Procedure to reset microprocessor functions and clear all stored memories.

Safety Check-out

Essential safety test before returning the unit to the customer.

Exploded View

Parts List

Block Diagram (120V/World Wide Models)

Block Diagram (230V Model)

Microprocessor Connection Diagram

Terminal Descriptions

IC Block Diagrams and Descriptions

Integrated Circuit Details

LA1836 (FM and AM Radio System)

Block diagram and function of the LA1836 IC.

μPC1225H (Power Amplifier Driver)

Block diagram and function of the μPC1225H IC.

NJM4558D-X (Operation Amplifier)

Block diagram and function of the NJM4558D-X IC.

µPC1346CS (RDS Decoder) Diagram

LM7001 (PLL Synthesizer and Controller) Diagram

Adjustment Procedures

Preparation and Inputs/Outputs

Setup for adjustments, including input signal and output load requirements.

Standard Knob Positions

Recommended initial settings for various controls before adjustment.

Idling Current Adjustment

Procedure to set idling current for the main circuit board.

Adjustment Procedures: FM and AM

FM Adjustment Steps

Detailed steps for adjusting FM IF/RF, Stereo Distortion, and Muting Level.

AM Adjustment Steps (120V)

Steps for AM adjustment for 120V models.

AM Adjustment Steps (230V/Worldwide)

Steps for AM adjustment for 230V and worldwide models.

Adjustment Point Diagrams

Schematic Diagram (Part A)

Schematic Diagram (Part B)

Central section of the schematic, including the microprocessor.

Schematic Diagram (Part C)

Right section of the schematic, showing power supply and output stages.

Schematic Diagram (Part D)

Schematic Diagram (Part E)

Lower part of the schematic, detailing various circuits and connections.

Schematic Diagram (Part F)

Right side of the schematic, showing tuner and power amp sections.

Schematic Diagram (Part G)

Connection details for microprocessor and related components.

Schematic Diagram (Part H)

Schematic Diagram (Part I)

Printed Circuit Board Parts List (Main)

Printed Circuit Board Parts List (Display)

Component list for the display circuit board.

Printed Circuit Board Parts List (Headphone/Secondary)

Component lists for headphone and secondary terminal boards.

Printed Circuit Board Parts List (Display cont.)

Printed Circuit Board Parts List (Tone Control)

Component list for the tone control circuit board.

Printed Circuit Board Parts List (Power Supply)

Component list for the power supply circuit board.

Printed Circuit Board Parts List (Voltage Selector/Power Switch)

Printed Circuit Board Parts List (Volume Circuit)

Component list for the volume control circuit board.

Printed Circuit Board Parts List (AC Outlet)

Component list for the AC outlet circuit boards.

Packing View

Related product manuals