Onkyo TX-866 - Remote Control Transmitter Operation; Transmitter Functions; Usage Guidelines

se
$595
Remote control transmitter RC-170S
Power Button (POWER) [10]
input Selector Buttons (TAPE-1,
TUNER, PHONO, CD, TAPE-2, VCR-2,
VCR-1/VDP) [10]
* When the TUNER button ts pressed, the
Sleep Button (SLEEP)
Press to set the power off timer. The sleep timer is a function which
turns off the power to the system from the time it ts set. When this
button is pressed, “90 MIN” ts displayed on the tuner’s display for 5
seconds, and the power goes off 90 minutes later. Each time the button
is pressed during 5 seconds, the timer setting changes, by 10 minute
intervals, such as 80, 70, 60.... While the sleep timer is operating,
the[SLEEP] indicator is lighted. If the sleep button is pressed during
this time, the amount of time remaining on the sleep timer is displayed,
and if the button is pressed during that display, 10 minutes will be
subtracted from that time.
lf the button is pressed when the panel display shows 10 minutes or
less, the sleep timer Is cancelled, and the power is not turned off.
station which was received previously {s
recalled. Selection of AM or FM should be
done on the main unit.
Phono Operation Button (PLAY/REJECT)
This button is used to operate the turntable.
The phono operation button can be used only
when the PHONO input selector button has
been pressed. Each time the phono operation
button is pressed, the remote control transmitter
|
[to
Speaker
Selector
Buttons
(SPEAKERS)
[10]
Tuner Operation Buttons (TUNER) [1712]
CLASS: Class selector button
@ PRESET P -: Preset memory DOWN/UP
buttons
Tape Operation Buttons
(DECK-A, DECK-B)
These buttons control Onkyo double cassette
tape decks that can be remote controlled. Use
alternately emits the play or reyect command.
CD Operation Buttons (CD)
the DECK-B buttons to contro/! single cassette
tape decks with the [FRE mark.
@/un : When this is pressed, the recording
stand-by mode is entered.
< - The tape plays, moving from night
aa
These buttons are used to operate an ONKYO
CD player with the RI mark.
> : Press this button to play the CD
player.
" : Press this button to pause the CD
—-al -e
play back. To resume disc play,
press the PLAY button.
DISC: Press to use for sequential selection
of discs in the order they were
loaded on the CD changer.
HM =:Press this button to stop the CD
player.
: Press this button to go back to the
beginning of the current track and
again to skip back to the previous
track.
: Press this button to skip to the next
track.
Ral Tet ob a da te
ONKYO
TidesPa md PE Ga dae Pb ociyt.
AULAD RE
rei DIN ob
to left, or, in the recording stand-by
mode, recording begins.
| ‘interrupts all operations.
> : The tape plays, moving from left to
right, or, in the recording stand-by
mode, recording begins.
: Fast forward from right to left.
' Fast forward from left to right.
Audio Muting Button (AUDIO MUTING)
and Indicator
This button temporarily switches off the sound
from the speaker or headphone. Pressing this
button will operate the TX-866/844 audio
muting circuit. The audio muting indicator
“AUDIO MUTING” wil! flash. Pressing the
button again or using the POWER button on
the remote control transmitter to turn the power
on will turn off the audio muting.
|
>>
Volume Buttons ( 4 UP, ¥ DOWN) [10]
Using the remote control transmitter
1. Remove the batteries if the remote control transmitter isnot going
to be used for a long time.
2. The batteries of the remote control transmitter must be replaced
periodically.
3. This unit uses infrared rays. Therefore, commands may not be
received properly if the front panel of this unit ts exposed to
bright light. To prevent this from occurring, place this unit so
that it is not dtrectly exposed to bright light.
4. lf this unit is placed inside an audio rack behind a glass door,
the door should not have colored giass or have any decorations
on it, since this could shorten the range or prevent commands
from being received.
5. Use of other infrared remote contro! devices in the same room
may cause interference.
6. The transmitter operates up to a distance of about five meters
(16 feet). The transmitting window must always be pointed at
the reception window when a command is sent to the
TX-866/844.
7. If this remote control transmitter does not operate properly,
confirm that the batteries are not dead. If the problem persists,
contact your Onkyo Service Center.
TX-866/844
Remote sensor
approx. 5m
(16 feet)
4
Remote control transmitter
— 9 —