INSTALLATION & OPERATION MANUAL
Visual Verification
Wi-Fi CAMERA module
Visual Verification
Wi-Fi CAMERA module
VXI-CMOD
VXI-CMOD
No.59-2753-0 1811-09
(Sold separately)
for VXI-ST/-AM/-DAM
for VXI-ST/-AM/-DAM
[VXI-ST]
[VXI-AM]
[VXI-DAM]
EN
Control Panel
VXI-CMOD
Internet
Alarm signal
Event recording
Wi-Fi router
Text notification
from a Control Panel
Visual verification
FEATURES
When the VXI-ST/-AM/-DAM generates an alarm signal,
the VXI-CMOD starts recording a 30 second video clip onto the microSD card.
The clip can then be reviewed via your smart phone from a remote location.
180 degree View Angle
Night vision with strong & wide IR light
Sensor trigger recording function with a 2 second pre-recording
Power from a control panel can be used for both the VXI-CMOD and the VXI-ST/-AM/-DAM
Smartphone
Newly added
INTRODUCTION
1
1-1 BEFORE INSTALLATION
- Read this INSTALLATON & OPERATION MANUAL carefully prior to installation.
- After reading, store this manual carefully in an easily accessible place for reference.
- This manual uses the following indications for correct use of the product, harm to you or other people and damage to your
assets, which are described below. Be sure to understand the description before reading the rest of this manual.
Failure to follow the instructions provided with this indication and improper handling may cause death or serious injury.
Failure to follow the instructions provided with this indication and improper handling may cause injury and/or property damage.
Warning
Caution
This symbol indicates prohibition.
Wi-Fi
The radio environment and a
smart phone may affect the
Wi-Fi communication state.
Warning
Caution
Adjust, set and check the VXI-ST/-AM/-DAM before starting the VXI-CMOD installation.
It is hard to access to the inside of the VXI-ST/-AM/-DAM after mounting the VXI-CMOD.
Refer to the manual of VXI-ST/-AM/-DAM.
NOTE
Field of view
Vertical:100°
Field of view
Horizontal:180°
PIR coverage
12 m max
Mounting height
0.8 to 1,2 m
1-2 CHOOSE LOCATION
1-3 LOCAL STORAGE
microSD card
For local storage use, a microSD card (not included)
is required.
Suitable microSD cards are as follows:
- FAT 32 format
- 32 GB max.
- Format in OPTEX Vision App
Power off the VXI-CMOD when installing microSD card.
To power down the VXI-CMOD disconnect the power or
remove the ribbon cable.
There is a 120 second boot up cycle.
Mounting
screws
< Accessories >
Camera mount
Ribbon
cable
External PCB
terminal
Waterproof
sponge
1-5 PARTS IDENTIFICATIONS
microSD card slot
IR-LED high/low
switch
Antenna internal/
external switch
Reset switch
Ribbon cable
connector
[Bottom view]
(without switch cover)
[Rear view]
(inside the body)
[VXI-CMOD]
CMOD cap
Lock screw
QR code label
for Device ID
[Top view]
(without the CMOD cap)
Power indicator
Lock screw hole
INSTALLATION
2
Disassemble the VXI-ST/-AM/-DAM while refering to
2 2-1 1 through 4 in the instllation instructions
of the VXI-ST/-AM/-DAM.
1
Make wiring knockout holes on the back box of the VXI-ST/-AM/-DAM.
2
Connect between terminals of VXI-ST/-AM/-DAM and the external PCB terminal.
NOTE
TROUBLE wiring not
required for VXI-ST.
Trouble
VXI-ST/-AM/-DAM
Power
(9.5 to 18 V DC)
to a control panel
to the VXI-CMOD
Power
(9.5 to 18 V DC)
Alarm
Tamper
Power
(over 18 to 24 V DC)
to a control panel
to the VXI-CMOD
Power
(9.5 to 18 V DC)
Alarm
Tamper
NOTE
A separate power supply of 9.5 to 18 V DC is required
for VXI-ST/-AM/-DAM when VXI-CMOD is powered
by a source over 18 to 24 V DC.
External PCB terminal
VXI-ST/-AM/-DAM
Set the ribbon cable
to the connector, and
attach the connector
cover.
Insert a
microSD card
Adjust the switch settings, if necessary.
Recommended Current draw
distance (max.)
(max.) at 12 V DC
12 m 1.0 A
6 m 400 mA
Position
high
low
(default)
[1]
[2]
[3]
[4]
- 1 -
IR-LED high/low switch
3
[5]
Open the
switch cover.
2.
[6]
Search for OPTEX Vision in the store.
OPTEX Vision
Visit either the App store or Google play.
Download and install the
OPTEX Vision application.
APP INSTALLATION
3
1
2
3
SETUP WIZARD
4
The external antenna (option) for the VXI-CMOD can extend the reach of the Wi-Fi communication.
Follow this instruction only if external antenna is needed.
Mount the bracket and set the main body.
Connect cables to the VXI-CMOD.
Set the antenna internal/external switch to EXT.
Main body
Bracket
Start the OPTEX Vision application.
Tap “Add Device” to start “Setup Wizard” .
1
2
If the PEU (Plug-in EOL) option is used on the VXI-ST/-AM/-DAM, remove it
from the terminal, then place it in the external PCB terminal of the VXI-CMOD.
External PCB terminal
NOTE
1 2 3
VXI-ST/-AM/-DAM
1.
Return the switch
cover to the original
position.
3.
Switch cover
+
-
SP TR
COM
AL TP TP
+
-
SP TR
COM
AL TP TP
+
-
SP TR
COM
AL TP TP
70 mm
(Recommended)
External PCB terminal
[7]
[8]
Accessing inside of the VXI-CMOD may be necessary in
the following process. Fix with the lock screw and attach
the CMOD cap at step 6.
Place the VXI-CMOD on the
VXI-ST/-AM/-DAM back box
temporarily.
NOTE
Ribbon cable
(included)
Wires
(not included)
Wires
(not included)
Jump to step 4 , if the OPTEX Vision App has already been installed.
Jump to step 5 , if the Wi-Fi network has already been set.
Requirement;
iPhone 5S with iOS 9.0 or later.
Android smartphone 5.X or later.
Do not drop the product and/or avoid scratches on the lens as it may affect it s performance.
Be careful to avoid pinching the wires when assembling.
Read and follow the instructions provided with the VXI-ST/-AM/-DAM.
‘
Get PDF file and also troubleshooting
information at the following website.
http://navi.optex.net/manual/50262
To Next Page
Need help?
General