To Next Page
W
William ToddJul 31, 2025
What to do if Optoma EW610ST shows Error (Over Temp.)?
- LlukevelazquezJul 31, 2025
If your Optoma Projector displays an 'Error (Over Temp.)' message, turn off the projector and allow it to cool down.
What to do if Optoma EW610ST shows Error (Over Temp.)?
If your Optoma Projector displays an 'Error (Over Temp.)' message, turn off the projector and allow it to cool down.
What to do if Optoma EW610ST Projector shows Error (Fan fail)?
If your Optoma Projector displays 'Error (Fan fail)', check the fan for any blockages and make sure that it is working as it should.
How to fix Optoma EW610ST Error (Lamp fail)?
To fix the 'Error (Lamp fail)' on your Optoma Projector, replace the lamp.
General| Matrix size | 0.65 \ |
|---|---|
| Projection distance | 0.5 - 2.5 m |
| Vertical scan range | 25 - 85 Hz |
| Horizontal scan range | 15 - 91 kHz |
| Projection technology | DLP |
| Contrast ratio (typical) | 3000:1 |
| Screen size compatibility | 44.64 - 223.21 \ |
| Projector native resolution | WXGA (1280x800) |
| Keystone correction, vertical | -40 - 40 ° |
| Resolution | 1600 x 1200 pixels |
| Aspect ratio | 16:10 |
| RS-232 ports | 1 |
| Compatibility | UXGA, SXGA, WXGA, HD, XGA, SVGA, VGA, Mac |
| Weight (imperial) | 6.834 lbs |
| Dimensions (WxDxH) | 306 x 243 x 113 mm |
| Power requirements | 100-240V, 50-60Hz |
| Connectivity technology | Wired |
| F-number (relative aperture) | 2.8 |
| Focal length range | 2.8 - 7.35 mm |
| 3D | Yes |
| Full HD | No |
| Service life of light source | 3000 h |
| Service life of light source (economic mode) | 4000 h |
| RMS rated power | 10 W |
| Serial interface type | RS-232 |
| USB 2.0 ports quantity | USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them. |
| Component video (YPbPr/YCbCr) in | 2 |
| Display number of colors | 1.073 billion colors |
| Power consumption (standby) | 1 W |
| Power consumption (typical) | 295 W |
| Operating temperature (T-T) | 5 - 40 °C |
| Operating relative humidity (H-H) | 0 - 85 % |
| Noise level | 31 dB |
| Product color | Black |
| Market positioning | Portable |
Weight and Dimensions| Weight | 3100 g |
|---|
Procedure for adjusting the projector's rod for image clarity.
Guide to re-write lamp usage hours in service mode.
Explains projector LED status indicators and error messages.
Details common troubleshooting steps for symptoms like auto shut down and 3D image issues.
Procedure for calibrating the projector's keystone correction.
Procedure for calibrating the projector's ADC settings.
Step-by-step guide for adjusting the projector's engine after replacement.
Instructions for testing the projector's network connectivity and IP settings.
Steps to configure PC network settings for projector connectivity.
Lists required software and hardware for system firmware upgrades.
Guide to enter firmware mode and check the current firmware version.
Details the equipment needed for PIC firmware upgrades via RS-232.
