To Next PageTo Next PageWhy is there no light on my Optoma HD70 Projector?
If your Optoma Projector has no light, ensure all connectors are securely connected and not broken. Then, check the lamp module, DC-DC, ballast, and main board.
How to fix image flicker on Optoma HD70?
If your Optoma Projector's image is flickering, try resetting the OSD menu. Also, ensure the signal cable and source are working correctly. Check the lamp module, color wheel, DMD board, and main board.
What to do if Optoma HD70 Projector shows a warning message when lamp life is nearing the end?
If your Optoma Projector displays a warning message indicating that the lamp life is nearing its end, you should contact your local reseller or service center to replace the lamp as soon as possible.
How to troubleshoot no power on Optoma HD70 Projector?
If your Optoma Projector shows no power, make sure the power cord and AC power outlet are securely connected. Also, check the lamp cover and interrupt switch. Ensure all connectors are securely connected and not broken. If the problem persists, check the DC-DC, ballast, and main board.
What to do if my Optoma Projector has no image?
If your Optoma Projector displays no image, first ensure the signal cable and source are working correctly. Next, check that all connectors are securely connected and not broken. If the issue continues, check the main board, DMD board, color wheel, DMD chip, and engine module.
Why does my Optoma HD70 auto shut down?
If your Optoma Projector is automatically shutting down, you can check the LED status, lamp, and lamp driver. Also, inspect the main board, thermal sensor, thermal switch, fan, color wheel, and photo sensor.
Why does my Optoma Projector show a garbage image?
If your Optoma Projector shows a garbage image, ensure the signal cable and source are working correctly. Then, check the main board and DMD board.
What to do if the Optoma HD70 remote control or control panel failed?
If your Optoma Projector's remote control or control panel has failed, start by checking the battery. If that's not the issue, check the remote control itself, the IR receiver, FPC, keypad, and main board.
How to resolve color abnormality on Optoma HD70 Projector?
If you observe a color abnormality on your Optoma Projector, try doing a reset of the OSD menu. You can also adjust the color wheel index. Check the main board, DMD board, and color wheel.
Why is my Optoma HD70 Projector making mechanical noise?
If your Optoma Projector is making mechanical noise, check the color wheel and the fan module.
Operating Environment| operating temperature | 5 to 35°C, 80% Max Humidity |
|---|---|
| storage temperature | -20 to 60°C, 80% Max Humidity |
| noise level | 30dB/29dB (STD/ECO) |
Power| power supply | AC Input 100-240V, 50-60Hz |
|---|---|
| power consumption | 250W, <13% at 110V |
| lamp life and type | 2000/3000 (STD/ECO) 200W P-VIP |
Display and Projection| brightness | 1000 ANSI Lumens |
|---|---|
| resolution | Native 720p (1280x720) |
| contrast ratio | 4000:1 in ImageAI Mode |
Ports & Interfaces| I/O connection ports | HDMI, Component Video, S-Video, VGA with Component & SCART Compatibility, Composite Video (RCA), RS-232, Dual IR Receivers, +12V Trigger |
|---|---|
| computer compatibility | SXGA+, WXGA, XGA, SVGA, VGA, VESA Standards, PC and Macintosh Compatible |
| video compatibility | NTSC, PAL, SECAM, HDTV (720p, 1080i), SDTV (480i/p, 576i) |
Weight and Dimensions| dimensions | 10.4” x 3.7” x 10.1” (264 x 94 x 257 mm) |
|---|---|
| weight | 5.6 lbs (2.54 kg) |
| throw ratio | 1.58-1.9:1 (Distance/Width) |
