IES-3162GC
10/ 100M
P7
P5
P3
P1
P8
P6
P4
P2
P15
P13
P11
P9
P16
P14
P12
P10
G2
G2 LNK /ACT
Gig abit Co mbo
G1
G2 LNK /ACT
PWR
PWR 1
PWR 2
Quick Installation Guide
Quick Installation Guide
Introduction
PRINTED ON RECYCLED PAPER
is managed Redundant Ring Ethernet switch with 16x10/100Base-T(X)IES-3162GC
ports and 2xgigabit combo ports. With completely support of Ethernet Redundancy
protocol, O-Ring (recovery time < 10/30ms over 250 units of connection), O-Chain,
MRP and MSTP/RSTP/STP (IEEE 802.1s/w/D) can protect your mission-critical*NOTE
applications from network interruptions or temporary malfunctions with its fast recovery
technology. O-Chain is the revolutionary network redundancy technology that provides
the add-on network redundancy topology for any backbone network, O-Chain allows
multiple redundant network rings of different redundancy protocols to join and function
together as a larger and more robust compound network topology. O-Chain providing
ease-of-use while maximizing fault-recovery swiftness, flexibility, compatibility, and
cost-effectiveness in one set of network redundancy topology. All function of IES-
3162GC can be managed centralized and convenient by a powerful windows utility —
Open-Vision. In addition, the wide operating temperature range from -40 to 75 C can
o
satisfy most of operating environment. Therefore, the switch is one of the most reliable
choice for highly-managed and Fiber Ethernet application.
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient: If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Safety & Warnings
Dimension
Panel Layouts
1. Power LED
2. PWR1 LED
3. PWR2 LED
4. R.M. status LED
5. Ring status LED
6. Faulty relay indicator
7. Console port
8. Link/Act LED for Ethernet port
9. Full/Half-duplex indicator
10. LAN ports
11. Link/Act LED for SFP ports
12. Combo ports
13. Reset button
14. Link/Act LED for Gigabit port
15. 100Mbps indicator for Gigabit port
Package Contents
Contents
DIN-rail Kit
CD
IES-3162GC
Pictures Number
X 1
X 1
X 1
Front View
Top Panel
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
QIG
Console Cable
X 2
X 1
X 1
Wall-mount Kit
7
1
2
3
4
5
6
Rear View
1
2
1
1. Wall-mount screw holes
2. Din-rail screw holes
2
1. Terminal blocks: PWR1,
PWR2 (12 48V DC), Relay-
2. Ground wire.
1
Installation
Step 1: Slant the switch and screw the Din-rail kit onto the back of the switch, right in
the middle of the back panel.
Step 2: Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch
clicks into the rail firmly.
DIN-rail Installation
Step 1: Screw the two pieces of wall-mount kits onto both ends of the rear panel of the
switch. A total of six screws are required, as shown below.
Step 2: Use the switch, with wall mount plates attached, as a guide to mark the
correct locations of the four screws.
Step 3: Insert a screw head through the large parts of the keyhole-shaped apertures,
and then slide the switch downwards. Tighten the screws for added stability.
Wall-mounting
Q I G
IES-3162GC
1907-200-E3162GCXX2-FX011
Mechanical Loading: Mounting of the equipment in the rack should be such that
a hazardous condition is not achieved due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the equipment
to the supply circuit and the effect that overloading of the circuits might have on
overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch uses
CAT 3,4,5,5e UTP cables to connect to any other network devices (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable
specifications.
Cable Types and Specifications:
Cable Type Max. Length Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000BASE-T Cat. 5 / Cat. 5e 100-ohm UTP UTP 100 m (328 ft) RJ-45
10
8
9
IES-3162GC
Version 2.1
154.0
96.4
13
12
PWR -1PWR -2
1A@ 24V
DC 50 -57V
V2- V 2+ V1- V1 +
Fau lt
Unit =mm (Tolerance ±0.5mm)
108.5
88.0
48.3
17.5
94.0
124.0
48.0
58.0
7.50
Ø5.00
Ø8.00
80.50
62.0
87.9
40.0
15.5
14.5
49.67
Ø4.00
Ø4.00
Industrial Managed Ethernet Switch
S W I T C H
I N D U S T R I A L
*NOTE : This function is available by request only.
IES-3162GC
10/10 0M
P7
P5
P3
P1
P8
P6
P4
P2
P15
P13
P11
P9
P16
P14
P12
P10
G2
G2 LNK/A CT
Gigab it Comb o
G1
G2 LNK/A CT
PWR
PWR1
PWR2
11
13
The product is open type, intended to be installed in and industrial control panel or an enclosure.
14
15
！
Warning [AVERTISSEMENT]
Take into consideration the following guidelines before wiring the device
[Tenez compte des directrices suivantes avant de câbler l’appareil.]
1. Terminal block is mating with Plug and suitable for 12-24AWG.
Torque value 4.5 lb-in.
[Le bornier est compatible avec les connecteurs et convient pour 12-24AWG.
Valeur de couple 4,5 lb-in.]
2. The temperature rating of the input connection cable should higher than 105°C
[La température de service nominale du câble d’entrée doit être supérieure à 105 °C]
* Indoor use and pollution degree II, it must be wiped with a dry cloth for clean up the
device and label.
* Utilisation en intérieur et degré de pollution II, il faut l'essuyer avec un chiffon sec
pour nettoyer l'appareil et son étiquette.
* Do not block air ventilation holes.
* Ne bouchez pas les orifices de ventilation.
* If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may be impaired.”
* Si l’appareil est utilise d’une maniere non specifiee par le fabricant, la protection
qu’il apporte peut se voir diminuee.”
* Shall be mounted in the Industrial Control Panel and ambient temperature is not
exceed 75 degree C
* doit être monté dans le panneau de commande industriel et la température ambiante
ne doit pas dépasser 75 degrés C
IES-3162GC
10/10 0M
P7
P5
P3
P1
P8
P6
P4
P2
P15
P13
P11
P9
P16
P14
P12
P10
G2
G2 LNK/ ACT
Gigab it Comb o
G1
G2 LNK/ ACT
PWR
PWR1
PWR2
To Next Page
Need help?
General
