What to do if my oticon CROS PX miniRITE R transmitter has no sound?
If there is no sound from your Oticon Hearing Aid transmitter, ensure that the transmitter is charged and turned on. Also, verify that the receiving hearing aid is also turned on.
Why is the LED light on my oticon Hearing Aid transmitter OFF when charging?
If the LED light on your Oticon Hearing Aid transmitter remains off when placed in the charger, it could be due to several reasons: * The charger may not be turned on, so verify that the charger’s power plug is correctly connected. * The transmitter or charger’s temperature might be too warm or too cold. Move the charger and transmitter to a location with a temperature between +5°C and +40°C or +41°F and +104°F. * Charging might be incomplete due to a high room temperature (exceeding +35°C or +95°F). Try reinserting the transmitter into the charger to complete the charging within approximately 15 minutes. * The transmitter might be incorrectly seated in the charger. Check the charging ports for foreign objects.
General| Model | CROS PX miniRITE R |
|---|---|
| Water Resistance | IP68 |
| Directional Microphones | Yes |
| Feedback Cancellation | Yes |
| IP Rating | IP68 |
| Type | CROS (Contralateral Routing of Signals) |
| Style | Receiver-in-the-ear (RIE) |
| Battery | Rechargeable |
| Wireless | Yes |
| Noise Reduction | Yes |
| Feedback Management | Yes |
| Tinnitus SoundSupport | Yes (Tinnitus SoundGenerator) |
Instructions on how to clean the microphone openings using the MultiTool brush.
Describes hearing aid sound behavior for CROS-only configurations.
Describes hearing aid sound behavior for BICROS configurations.
Volume control for hearing aids with a single push button.
Volume control for hearing aids with a double push button.
Warning about the dangers of children swallowing small parts and batteries.
Warning about severe risks from swallowing or inserting lithium-ion batteries.
Warning about using the transmitter in environments with explosive potential.
Information on potential transmitter malfunction and its implications.
Precautions for users with active medical implants like pacemakers.
Instructions to remove the transmitter before medical procedures involving radiation or electric fields.
Warnings regarding exposure to extreme heat and damaging chemicals.
Potential side effects like skin irritation or earwax accumulation.
Information on electromagnetic interference and its impact on transmitter performance.
Recommendation to use only manufacturer-approved accessories.
Prohibition of unauthorized modifications to the transmitter.
Information and warnings about the transmitter's rechargeable battery.
Guidance for situations where the earpiece detaches in the ear canal.
Considerations for using the transmitter in challenging acoustic environments.
Troubleshooting steps for when the transmitter LED is OFF in the charger.
Troubleshooting steps for a blinking GREEN LED when the transmitter is in the charger.
Troubleshooting steps for a blinking ORANGE LED when the transmitter is in the charger.
Troubleshooting steps for when no sound is transmitted.
Troubleshooting steps for unexpected beeping sounds from the transmitter.
Technical specifications and certification information for the USA and Canada.
Explanation of the general warning symbol used in the booklet.
Explanation of the manufacturer identification symbol.
Explanation of the CE conformity marking.
Explanation of the symbol for electronic waste disposal.
Explanation of the RCM mark for Australian/New Zealand compliance.
Explanation of the Ingress Protection (IP) code.
Explanation of the symbol indicating an RF transmitter.
Explanation of the Medical Device symbol (MD).
Explanation of the symbol indicating protection from moisture.
Explanation of the caution symbol for warnings and cautions.
Explanation of the symbol for catalogue number (REF).
Explanation of the symbol for serial number (SN).
Explanation of the battery recycling symbol.
Explanation of the symbol for temperature limits.
Explanation of the symbol for humidity limitations.
Explanation of the RFID symbol for identification tags.
Details on sounds and LED lights related to volume adjustments.
Details on sounds and LED lights indicating device ON/OFF status.
To Next Page
