This document serves as an important instruction and operating manual for various models of electric fireplaces, specifically WM36DR, WM42DR, WM50DR, WM60DR, WM72DR, WM84DR, and WM100DR. It outlines crucial safety information, installation procedures, operational guidelines, and maintenance instructions to ensure safe and effective use of the appliance.
Function Description:
The device is an electric fireplace designed for supplemental heating and aesthetic purposes. It creates the visual effect of a real fireplace with a smouldering glow of flames, offering rich and colorful flame and log fuel color options. It produces a hot current of air for heating, with automatic and constant temperature control. The fireplace can be used as both a wall-mounted unit or a fully embedded (recessed) installation. It features a timer function (1 to 9 hours) and 5-gear flame brightness adjustment. The unit is operated via both a remote control and a manual panel switch.
Important Technical Specifications:
- No Venting Required: The fireplace does not require any external venting, simplifying installation.
- Power Supply: 120V AC; 60 Hz.
- Power Consumption: 1500 Watts (Maximum Heat Output).
- Maximum Heat Output: 1500 W (5120 BTU).
- Maximum Heating Area: 400 square feet.
- Protection Class: I.
- Light Bulb: LED.
- Temperature Limiting Control: Equipped with a safety feature that automatically turns the heater OFF if it reaches an unsafe temperature (212°F / 100°C).
- Plug Type: Designed for use on 120 volts with a three-blade grounding-type plug. An adapter (shown at C in the manual) is available for connecting to two-slot receptacles, provided the green grounding lug is connected to a permanent ground. The adapter should not be used if a three-slot grounded receptacle is available.
Usage Features:
- Installation Flexibility: Can be installed as a wall-mounted unit or fully recessed into a wall. Detailed instructions are provided for both methods, including specific dimensions for recessed installation for each model.
- Remote Control and Manual Operation: The fireplace can be controlled using either the provided remote control or the manual touch display panel located on the front bottom right of the appliance. The control panel POWER switch must be ON to use the remote control.
- Adjustable Settings:
- Power ON/OFF: Turns the appliance on or off.
- Flame Color: Controls flame color change, offering 13 different colors (F01-F13) that cycle through.
- Log Fuel Color: Controls log fuel color change, also offering 13 different colors (C01-C13) that cycle through.
- Heater Control: Initiates the heater, with options for OFF, LO (750W warm air), and HI (1500W hot air). The heater functions cycle from OFF-LO-HI.
- Timer: Allows setting the heater to turn off after a specified duration, with 9 settings from 1 to 9 hours.
- Temperature Control: Adjusts the desired temperature setting. The display shows setting circles, and the temperature unit can be switched between °C and °F by pressing the button for 10 seconds.
- Flame Brightness: Offers 5 levels of flame brightness adjustment (L1-L5).
- Log Fuel Brightness: Offers 5 levels of log fuel brightness adjustment (E1-E5).
- Media Options: The fireplace allows for interchangeable media, specifically LOG and Glass Media (Crystal Embers and Drift Wood Fire Logs are mentioned).
- Safety Precautions:
- Always read and understand the entire owner's manual before use.
- Keep combustible materials (furniture, bedding, papers, clothes, curtains) at least 0.9 m (3 feet) from the front, sides, and rear of the heater.
- Exercise extreme caution when used near children or invalids, or when left operating unattended.
- Do not operate if malfunctioning; disconnect power and have it inspected by a reputable electrician.
- Do not use outdoors.
- Do not insert foreign objects into ventilation or exhaust openings.
- Do not block air intakes or exhaust.
- Do not use in areas with gasoline, paint, or flammable vapors/liquids.
- If an audible or visual alarm sounds (indicating excessive heat), immediately turn off the heater and inspect for blocked airflow. Do not operate with the alarm sounding.
- Never use an extension cord.
- Ensure the mains cable remains at the back of the appliance and does not contact hot elements.
- The power plug should be accessible after installation.
- The heater must not be located immediately below a socket-outlet.
- Not intended for use by young children or infirm persons without supervision.
- Do not use in the immediate surroundings of a bath, shower, or swimming pool.
- Do not cover the heater to avoid overheating.
- Sharp edges are present; handle with caution.
Maintenance Features:
- Cleaning:
- Always turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or relocating.
- Never immerse in water or spray with water.
- Metal Parts: Buff with a soft cloth slightly dampened with a citrus oil-based product. Do not use brass polish or household cleaners.
- Glass: Use a good quality glass cleaner sprayed onto a cloth/towel, then dry thoroughly with a paper towel or lint-free cloth. Never use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
- Vents: Use a vacuum or duster to remove dust and dirt from the heater and vent areas.
- Plastic: Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water. Never use abrasive cleansers, liquid sprays, or any cleaner that could scratch the surface.
- Battery Replacement: The remote control uses two AAA batteries (not included). Instructions for installation are on the remote control battery compartment. Never dispose of batteries in fire; dispose of them at a local hazardous material processing center.
- Troubleshooting Temperature Limiting Control: If the heater automatically turns off due to overheating, unplug the power cord, turn the ON/OFF switch to OFF, wait 5 minutes, inspect for blocked vents, then plug the power cord back in. If the issue persists, have outlets, wiring, and breaker box inspected by a professional.
- Service: Components should only be serviced by an approved electro technician. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person.
The product comes with a limited warranty to the original purchaser, covering defects in material and workmanship for one year from the date of purchase. Missing or initially defective parts will be replaced free of charge. The original dated sales receipt is required for all warranty claims. The warranty does not cover damage from transport, glass, light bulbs, batteries, transportation, labor, or other issues not associated with manufacturing. This product is for residential use only; commercial use voids all warranties. The warranty is also voided by tampering, incorrect assembly, improper care, misuse, abuse, use with wrong power source, water damage, outdoor use, excessive use, commercial application, or use as a primary heat source. The product is intended for supplemental heating purposes only.
To Next Page
Need help?
General
