P.Lindberg QJY230C-E - User Manual

Other manuals for P.Lindberg QJY230C-E

Questions and Answers

J
Jerry VincentAug 17, 2025
Why is my P.Lindberg QJY230C-E Lifting columns automotive lift not raising a vehicle but operates without a load?
- M
  Melissa KimAug 18, 2025
  This issue may arise due to several reasons. The electrical motor might not have enough power, or there could be impurities in the hydraulic valves. Another possibility is that the safety valve is set too low, or the automotive lift is overloaded. To address this, check the power supply, remove and clean the valves (and potentially the entire hydraulic system), adjust the safety valve, and verify that the vehicle's weight is within the lift's capacity.
K
Kenneth HoAug 20, 2025
What to do if the raising speed of P.Lindberg QJY230C-E Lifting columns is very slow and oil foam comes out of the oil filler hole?
- M
  mcdonalddavidAug 20, 2025
  If the raising speed is slow and oil foam is present, it indicates that air has mixed with the oil, the feed hose is sucking in air, or the oil return hose is loose. To resolve this, change the hydraulic oil and tighten all supply and return hoses.
E
Edward TaylorAug 23, 2025
What to do if P.Lindberg QJY230C-E Lifting columns automotive lift lowers slowly without pushing the lower button?
- C
  Christopher WuAug 23, 2025
  If your automotive lift lowers slowly without pressing the lower button, it could be due to impurities in the hydraulic valves or oil leaks in hose connections. You should remove and clean the valves, clean the entire system if required, and repair any defective hydraulic connections.
K
kathrynnelsonAug 25, 2025
Why P.Lindberg QJY230C-E Lifting columns automotive lift does not lift uniformly on both sides?
- M
  melindachristianAug 26, 2025
  Uneven lifting on both sides typically occurs because the equalisation wires are incorrectly adjusted or the automotive lift isn't correctly installed on a level surface. Adjust the equalisation wires to fix this. If needed, use equalisation plates under one of the columns to ensure the automotive lift is level.
Z
zbatesAug 27, 2025
What to do if hydraulic engine of P.Lindberg QJY230C-E is not operating?
- S
  Scott BentonAug 27, 2025
  To resolve this, replace fuses or reset the automatic fuse. Troubleshoot and repair the fault. Replace the defective cables. Replace the electrical motor.
L
lcarlsonAug 30, 2025
What to do if the hydraulic engine operates but P.Lindberg QJY230C-E Lifting columns automotive lift does not?
- N
  Natalie SimpsonAug 30, 2025
  If the hydraulic engine runs but the lift doesn't, the electrical lower valve may be open, the hydraulic pump could be sucking in air, or the hydraulic oil level might be too low. Check the cable connections and replace the valve if necessary. Also, inspect all hose connections and add hydraulic oil HVI 32 or HVI 46 until it reaches the correct level (10 l when filling from new).
J
Jessica WilsonSep 1, 2025
Why are the lifting bolts loose on my P.Lindberg QJY230C-E?
- S
  Sarah WhiteSep 2, 2025
  Loose lifting bolts are generally caused by a drilled anchor hole that's too big or concrete that isn't strong enough. Fill the anchor hole with anchor adhesive, or move the automotive lift and drill new holes with the correct dimension. You could also cast a new floor.
D
Derek YatesSep 4, 2025
What to do if the hydraulic engine operates but the P.Lindberg QJY230C-E do not?
- M
  Michael ColemanSep 4, 2025
  If the hydraulic engine runs but your P.Lindberg Lifting columns aren't working, there are several potential causes. First, the electrical lower valve might be open; in this case, check the cable connections or replace the valve. Second, the hydraulic pump could be sucking in air, so inspect all hose connections. Finally, the hydraulic oil level might be too low; if so, fill it with hydraulic oil HVI 32 or HVI 46 (the initial filling amount is 10 liters).
J
John WatsonSep 7, 2025
Why is my P.Lindberg Lifting columns raising speed very slow and oil foam comes out of the oil filler hole?
- H
  Heather HaysSep 7, 2025
  If your P.Lindberg Lifting columns are raising very slowly and oil foam is coming out of the oil filler hole, it could be due to a few reasons. It's possible that air has mixed with the oil, in which case you should change the hydraulic oil. Another possibility is that the feed hose is sucking in air, so make sure to tighten all supply hoses. Lastly, the oil return hose might be loose, so ensure all hoses are tightened.
T
Timothy OlsenSep 9, 2025
What to do if the hydraulic engine operates, the P.Lindberg Lifting columns operates without a load, but will not raise a vehicle?
- E
  Emily HowellSep 9, 2025
  If the hydraulic engine operates, and the P.Lindberg Lifting columns operates without a load, but it won't raise a vehicle, there are several potential reasons. The electrical motor might not have enough power, so check the power supply. There could be impurities in the hydraulic valves, so remove and clean them. The safety valve might be set too low, so adjust it. Finally, the automotive lift might be overloaded, so check the vehicle's weight.