PAC C2R-CHY4 User Manual

Pacic Accessory Corporation - Santa Ana, CA 92705
techsupport@pac-audio.com • Voice: 866-931-8021 • Fax: 714-835-3233 • www.pac-audio.com
DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the C2R-CHY4 be held liable for consequential damages sustained in
connection with the C2R-CHY4. The manufacture and it’s distributors will not, nor will they authorize any representative or any other individual to assume
obligation or liability in relation to the C2R-CHY4 other than its replacement.
10-13-08
J1850
Class 2
VPW
Class 2
J1850
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
Arbitration
EOD
CRC
1 0 0 0 1 1 1 0 1 1 1 1 0 0 1 0 0 1 1 0 1 1 0 0
1 1 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 1 0 0 1 1 0 0
Class 2
Class 2
J1850
Radio Replacement Interface
with Nav Outputs for all Chrysler
Dodge / Jeep CANbus Vehicles With
or Without Premium Audio Systems
C2R-CHY4
Installation Notes:
1. Only one of the two provided radio harnesses will be used. Remove the factory installed radio
to determine the correct harness for your particular vehicle.
2. Vehicles without a factory amplier: Connect the aftermarket radio’s front and rear speaker
wires to the 22 pin plug.
3. Vehicles with a factory amplier: The factory amplier only accepts two audio channels
(left and right). The amplier’s fading is controlled by data communication from the factory radio.
The aftermarket radio does not have the ability to control the amplier’s fader. Connect the front
outputs of the aftermarket radio to the rear inputs of the 22 pin radio connector. This will
allow navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used.
4. Vehicles with a manual transmission will not support a reverse trigger output.
5.The accessory output wire is located on the 11 pin CAN INTERFACE harness - connect this wire to the radio’s accessory wire. The accessory
wire supplies +12v, 1 amp max when key is in the accessory or ignition position (g. 1: If more current is needed).
6. 11 pin plug (to CAN INTERFACE):
Blue/White - Connect this wire to the radio’s amplifier remote output. Connect this wire with or without OEM amp present!
White/Green - SWC output.
Green - Connect this wire to the radio’s reverse input wire only.
Orange/White - Connect this wire to the radio’s Illumination input wire only.
Violet/White - Connect this wire to the radio’s VSS input wire only.
Red/White - Connect this wire to the radio’s parking brake input wire only.
Note: Do not connect these wires to any circuit other than the radio’s wire harness.
7. 11 pin plug (to SWC INTERFACE):
This is a quick connection to a radio specic SWC interface. No additional connections are
necessary other than radio control connections. Plug the radio specic SWC interface in to
this connector and program the radio specic SWC interface for version 2. Do not cut the
loops. Refer to the SWC interface instruction manual for the radio specic control function
programming order.
8. Refer to the aftermarket radio’s instruction manual for testing VSS, Reverse, Parking Brake
and Illumination outputs. For the most current and Up-to-Date application guide please
visit www.pac-audio.com
1.
2.
3.
4.
5.
6.
Fig. 1
(using a SPDT relay)
85 86
30
87
87a
Ground
High Current 12v
(Fused)
12v Acc.
From
Interface
New High
Current Output
Diode 1N4005
or equivelant
9
1
23456
78
1011
Accessory Output +12volts 1amp max.
Pacific Accessory Corporation
Chrysler Radio Replacement Interface
2005 & up
9 1
9
1
23456
78
1011
9 1
SWC Interface. Program for Version 2
Radio Specific Steering
Wheel Control Interface
(Sold Separately)
Program SWC
Interface for Version 2.
CAN INTERFACE
Navigation outputs and
Amplifier Remote Input
See Chart for wire color
descriptions.
Radio Connections. See aside
Chart for color description.
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
White / Black Front L - input
Grey Front R + input
Grey / Black Front R - input
Green Rear L + input
Green / Black Rear L - input
Purple Rear R + input
Purple / Black Rear R - input
Radio Connection Chart:
(Read the Installation Notes before making
connections to the provided radio harness)
CAN Interface Connection Chart:
Red Acc. Output (1 amp)
Red / White P.B. Output (-)
Purple / White VSS Output (Pulse)
Orange / White Illum. Output (+)
Green Reverse Output (+)
White / Green SWC Output
Blue / White Amp Turn On Input

PAC C2R-CHY4 Specifications

General

Product Type	Radio Replacement Interface
Steering Wheel Control Retention	Yes
Amplifier Turn-On	Yes
Interface Type	Wired
Color	Black
Material	Plastic
Compatibility	Chrysler/Dodge/Jeep
Vehicle Compatibility	Chrysler, Dodge, Jeep
Navigation Outputs	Yes