Paccar BRADEN/GEARMATIC BG8B User Manual (English)

Questions and Answers:

D
Dominique HeathAug 5, 2025
Why is my Paccar BRADEN/GEARMATIC BG8B Industrial Equipment winch running hot?
- M
  markharrisAug 5, 2025
  The Paccar Industrial Equipment winch may run hot due to several reasons. It could be caused by a plugged heat exchanger, which requires thorough cleaning of both the exterior and interior. The hydraulic oil level in the reservoir might be too low or too high, requiring adjustment to the proper level. The hydraulic pump might not be operating efficiently; in this case, tune or adjust the prime mover, check the suction line for damage, or, if belt-driven, replace or tighten slipping belts. If the pump is worn, it should be replaced. Excessively worn or damaged internal winch parts can also cause overheating, necessitating disassembly of the winch to inspect and replace worn parts.
K
Kayla MorrisAug 10, 2025
What to do if the Paccar BRADEN/GEARMATIC BG8B winch will not hoist the rated load?
- Y
  Yesenia PaulAug 10, 2025
  If your Paccar Industrial Equipment winch is not hoisting the rated load, there are several possible causes. The winch may be mounted on an uneven or flexible surface, causing distortion. Reinforce the mounting surface and use shims to level the winch, and then evenly retighten all winch mounting bolts to the recommended torque. The system relief valve may be set too low; check the relief pressure by installing a gauge into the brake valve's inlet port and apply a stall pull load while monitoring the pressure, then adjust the relief valve as required. Note that a contaminated or worn-out relief valve may require disassembly or replacement.
P
paulajonesAug 14, 2025
What to do if my Paccar BRADEN/GEARMATIC BG8B winch brake will not hold a load?
- L
  Lori GainesAug 14, 2025
  If the brake on your Paccar Industrial Equipment winch will not hold a load with the control lever in neutral, it could be due to excessive system back pressure acting on the brake release port. Another reason could be worn or damaged brake discs. Also, the brake clutch might be slipping; in this case, drain the old gear oil, flush the winch with solvent, thoroughly drain the solvent, and refill the winch with the recommended planetary gear oil. The brake clutch may also be damaged or worn, requiring disassembly and inspection.
J
Joseph KlineAug 18, 2025
Why does my Paccar BRADEN/GEARMATIC BG8B Industrial Equipment winch chatter while raising a load?
- C
  Cheryl LewisAug 18, 2025
  The Paccar Industrial Equipment winch may chatter while raising a rated load if the controls are being operated too quickly. In this case, conduct operator training as required.
N
Nicholas ConnerAug 27, 2025
What causes oil leaks from the vent plug in Paccar BRADEN/GEARMATIC BG8B Industrial Equipment?
- A
  amandawangAug 27, 2025
  Oil leaks from the vent plug in Paccar Industrial Equipment can be caused by a defective motor seal due to high system back pressure or contaminated oil. System back pressure must not exceed 150 PSI. Inspect the hydraulic system for restrictions in the return line from the control valve to the reservoir, and ensure the control valve and plumbing are properly sized to the winch motor. Oil analysis may indicate contamination has worn the motor shaft and seal. Thoroughly flush the entire hydraulic system and install new filters and oil. Install a new motor seal.
T
Tracy WeaverAug 31, 2025
Why wire rope does not spool smoothly on the drum of my Paccar BRADEN/GEARMATIC BG8B?
- J
  Jessica WashingtonAug 31, 2025
  If the wire rope does not spool smoothly on the drum of your Paccar Industrial Equipment, the winch may be mounted too close to the main sheave, causing the fleet angle to be more than 1-1/2 degrees. Check the mounting distance and fleet angle, and reposition the winch as required. Also, the winch may not be mounted perpendicular to an imaginary line between the center of the cable drum and the first sheave. It is also possible that you are using the wrong lay rope. Consult a wire rope manufacturer for a recommendation of wire rope that best suits your application, and replace the wire rope and conduct operator/rigger training as required.

Paccar BRADEN/GEARMATIC BG8B Specifications

General

Manufacturer	Paccar
Model	BRADEN/GEARMATIC BG8B
Type	Winch
Rated Capacity	8, 000 lbs
Brake Type	Automatic disc brake
Line Pull	8, 000 lbs
Mounting	Base mounted
Typical Application	Utility