Pacific Power Source AFX Series - Page 5

AFX SERIES® OPERATION MANUAL
CONTENTS
Entire Contents Copyright

2016 by Pacific Power Source, Inc. (PPS) • All Rights Reserved • No reproduction without written authorization from PPS.
AFX Series Power Source Operation Manual Page 5 of 274
6.4.8 Waveform Smoothing Filter............................................................................................................................. 85
6.4.9 AUTO RMS Function – Steady State ................................................................................................................ 86
6.4.10 Extended AC Voltage Range Operation ........................................................................................................... 87
6.5 MEAS – MEASUREMENTS Screens ....................................................................................................... 90
6.5.1 Measurements Screen by Phase ..................................................................................................................... 90
6.5.2 Three Phase Measurement Screen Soft Keys ................................................................................................. 91
6.5.3 Individual Phase Measurement Screen Soft Keys ........................................................................................... 93
6.6 TRAN- TRANSIENTS Screens ................................................................................................................. 94
6.6.1 Transient List Parameters ................................................................................................................................. 94
6.6.2 Transient Edit Mode ......................................................................................................................................... 97
6.6.3 Transient Execution Modes ............................................................................................................................. 98
6.6.4 Transient Entry Modes ................................................................................................................................... 100
6.6.5 Multiple User Waveforms in Transients ........................................................................................................ 101
6.6.6 AUTO RMS Function – Transients .................................................................................................................. 101
6.7 CONF – CONFIGURATION Screens ..................................................................................................... 103
6.7.1 UTILITY – UNIT CONFIGURATION Screen ...................................................................................................... 104
6.7.2 USER LIMITS SETTINGS Screen ....................................................................................................................... 106
6.7.3 RAMP TIME & SLEW RATE SETTINGS Screen ................................................................................................ 107
6.7.4 PROGRAM MEMORY Screen ......................................................................................................................... 109
6.7.5 CSC CONFIGURATION Screen ........................................................................................................................ 110
6.8 SYST – SYSTEM Screens ....................................................................................................................... 111
6.8.1 SYSTEM MENU 1 ............................................................................................................................................. 112
6.8.2 SYSTEM MENU 2 ............................................................................................................................................. 112
6.8.3 ERROR / EVENT QUEUE Screen ..................................................................................................................... 113
6.8.4 FAULT INFORMATION Screen ........................................................................................................................ 113
6.8.5 INTERFACE Screen .......................................................................................................................................... 114
6.8.6 UNIT INFORMATION Screen .......................................................................................................................... 123
6.8.7 PARALLEL UNITS Screen ................................................................................................................................. 124
6.8.8 SYSTEM SETTINGS Screen .............................................................................................................................. 125
6.8.9 EXTERNAL STORAGE MANAGEMENT Screen ............................................................................................... 126
6.8.10 CALIBRATION MENU Screen .......................................................................................................................... 127
6.8.11 FIRMWARE UPDATE Screen ........................................................................................................................... 128
6.8.12 REMOTE SUPPORT Screen ............................................................................................................................. 129
7 Rear Panel, Connectors and Protection .................................................................................. 130
7.1 OUTPUT Terminals .............................................................................................................................. 130
7.1.1 Output Power Connector Rating and Isolation ............................................................................................. 130
7.1.2 Wire Size .......................................................................................................................................................... 131
7.1.3 Connecting a UUT ........................................................................................................................................... 131
7.2 External Voltage Sense Input Terminals ............................................................................................ 132
7.2.1 External Voltage Sense Connector Rating and Isolation .............................................................................. 133
7.2.2 Load Connection without External Voltage Sense ........................................................................................ 133
7.2.3 Load Connection with External Voltage Sense. ............................................................................................ 133
7.3 System Interface Bus Connectors ....................................................................................................... 134
8 Remote Control Programming ................................................................................................ 135
8.1 Overview .............................................................................................................................................. 135
8.1.1 Programming Conventions and Notations .................................................................................................... 135
8.1.2 Command Terminators .................................................................................................................................. 136
8.2 Remote Control Command Descriptions by Subsystem ................................................................... 137
8.3 Calibration Commands ........................................................................................................................ 138
8.3.1 UPC Specific commands. ................................................................................................................................ 140
8.4 Measurement Commands .................................................................................................................. 141
8.4.1 Voltage Measurement Commands ............................................................................................................... 141
8.4.2 Frequency Measurement Commands .......................................................................................................... 142