Panamax M4320-PRO - User Manual

1 2 3 4 5 6 7 8
UNSAFE VOLTAGE
BREAKER
WIRING FAULT
TEMPERATURE
20 A
BRIGHTNESS
OUTLET STATUS
REBOOT 1 REBOOT 2
M4320-PRO
B
LT
Blue
™
ENABLED
VOLTS
Power Management with Control System Interactive Functionality.
• 20 Amp Capacity M4320-PRO
• 8 Individually Controllable Rear Panel Outlets
• Fully Programmable
• TCP/IP (BlueBOLT™) Installed
• RS-232 Card (Included, not installed)
• Linear Filtration with 3 Isolated LiFT Filter Banks, 76db (5 kHz - 250 kHz), 46 db (250 kHz - 1 MHz)
• One Isolated Filter Bank for High Current Devices, 60db (5 kHz - 450 kHz), 46 db (450 kHz - 1 MHz)
• Front Panel Circuit Breaker
• Integrated Front Rack Ears
• 12 Volt Input Triggering
• Detachable 10 ft. Power Cord - 20A plug
• AVM & Protect-or-Disconnect Circuitry
M4320-PRO Instructions
INS00860 REV. D 5/10
Important: You will need the BlueBOLT-CV1’s unique MAC address and challenge key (provided on the 2 labels
attached to the cover of the Quick Start Guide which is included in the M4320-PRO packaging). One label is
permanently adhered to the Quick Start Guide and the other is removable for your convenience.
B
L T
Blue
™

ENABLED

Summary

Features Descriptions

BlueBOLTTM

Remote Power Management technology providing secure, hosted IP system control.

LIFT Technology EMI;RFI Noise Filtration

Filters electromagnetic interference and radio frequency interference to improve A/V performance.

Automatic Over & Under Voltage Protection (AVM)

Monitors AC line voltage for unsafe conditions and disconnects equipment.

4 Isolated Outlet Banks

Provides noise isolation between outlet banks for cleaner power distribution.

Sequential Startup;Shutdown

Eliminates transients by sequencing power-up and shut-down delays for components.

Important Safety Instructions

Front Panel Features Overview

Preset Profile Information

PROFILE 1 (P1)

Default outlet sequencing with specific startup, shutdown, and trigger delays.

PROFILE 2 (P2)

A/V + Modem outlet sequencing with different delay parameters.

PROFILE 3 (P3)

A/V + Extended Delays outlet sequencing with longer delay timings.

PROFILE 4 (P4)

Network + Control Delays outlet sequencing for various devices.

Rear Panel Features Overview

Getting Setup for BlueBOLT

SYSTEM SETUP #1 Network Equipment Powered by M4320-PRO (devices in same room)

Steps to connect network equipment powered by the M4320-PRO in the same room.

SYSTEM SETUP #2 Network Equipment NOT-Powered by M4320-PRO (devices in separate rooms)

Steps to connect network equipment not powered by the M4320-PRO in separate rooms.

BlueBOLT Online Registration

Instructions for registering the BlueBOLT™™ enabled device online via www.mybluebolt.com.

Troubleshooting

RS-232 Installation (optional)

RS-232 Command Set and Telnet; Protocol Specification

3. CONTROLLER COMMANDS

4. QUERIES

3.7 SET REBOOT DELAY

3.8 SET DELAY

3.12 SET PROFILE

4.1 FAULT STATUS

5. Responses and Warning Messages

M4320-PRO Specifications

Panamax M4320-PRO Specifications

General

Type	Surge Protector
Maximum Surge Current	4320 Joules
Outlets	12
Coaxial Protection	Yes
Telephone Protection	Yes
USB Ports	2
Warranty	Lifetime
Protection Modes	L-N, L-G, N-G
UL Voltage Protection Rating	330V
Maximum Spike Voltage	6000V
Noise Filtration	Yes
Automatic Voltage Shutoff	Yes
Under-Voltage Shutoff	Yes
Over-Voltage Shutoff	Yes
LAN Protection	Yes
Telco Protection	Yes
USB Charger	Yes
Voltage Protection Rating	330V
Response Time	< 1 nanosecond
Non-Filtered Outlets	0
USB Charging Ports	2
Cord Length	8 ft