Panasonic Aquarea WH-ADC0309J3E5C - Page 74

74 Aquarea air-to-water heat pumps - Planning and installation manual - 02/2022
Product Description
4
Connections
a
A B
b
d
e
c
Connection
PAW‑
TD20C1E5
PAW‑
TD30C1E5
PAW‑
TD30C1E5‑HI
a Hot water outlet 3/4“ BSP
female
3/4“ BSP
female
3/4“ BSP
female
b Circulation pipe inlet 3/4“ BSP
female
3/4“ BSP
female
3/4“ BSP
female
c Supply water inlet from
the heat pump
3/4“ BSP
female
3/4“ BSP
female
3/4“ BSP
female
d Return water outlet to the
heat pump
3/4“ BSP
female
3/4“ BSP
female
3/4“ BSP
female
e Fresh water inlet 3/4“ BSP
female
3/4“ BSP
female
3/4“ BSP
female
Unit: Inches (")
Note: Schematic gure of TD30C1E5 shown as an example for all models.
Dimensions
A
B
C
D
E
e
d
c
b
a
F
Dimension
PAW‑
TD20C1E5
PAW‑
TD30C1E5
PAW‑
TD30C1E5‑HI
A 1,270 1,750 1,750
B 155 155 155
C 266 266 266
D 866 866 1,245
E 966 1,036 1,245
F (Ø) 595 595 595
Unit: mm
Note: Schematic gure of TD30C1E5 shown as an example for all models.
Technical data
Domestic hot water tanks Stainless steel hot water tanks
Model PAW‑TD20C1E5 PAW‑TD30C1E5 PAW‑TD30C1E5‑HI
Water volume l 192 284 280
Max. water temperature °C 75 75 75
Dimensions Height / Diameter mm 1,270 / 595 1,750 / 595 1,750 / 595
Weight(net/incl.waterlling) kg 50 / — 61 / — 65 / -
Power of electric tank heater kW 1.5 1.5 1.5
Power supply V 230 230 230
Material inside the tank Stainless steel Stainless steel Stainless steel
Heat exchanger surface m²
1.8 1.8 2.35
Energy loss in standby at 65 °C
1
kWh/24 h 1.01 1.18 1.18
3 way valve accessory PAW-3WYVLV-HW or CZ-NV1 Optional Optional Optional
20 m temperature sensor cable included Yes Yes Yes
Energy losses W 42 49 49
Energyefciencyclass
2
A A A
Warranty of the inner vessel 2 Years 2 Years 2 Years
Maintenance required No No No
1 Insulation tested according to EN 12897
2 Energy e󰀩ciency class scale from A+ to F.
Note: Stainless Steel Tanks are produced by OSO.
16.02.2022, cH
According to 2022.02.01_ii_A2W21_EN_V1_Korr
(Thomas):
- “A” image replaced, to not show the additional
thermostat
- “B” image and “Dimensions” image replaced to
show TD30C1E5 (instead of TC30C1E5-HI), so that
the same image is used in all occurrences
- dimension “F” deleted from image
- in the table, “F” replaced by “E”, and “G” replaced
by “F”; now the numbers should be correct
- note added