What to do if my Panasonic Desktop external display does not work normally?
If the external display on your Panasonic Desktop does not support the power saving function, it may not work normally when the computer enters the power saving mode. In this case, turn off the external display.
What to do if my Panasonic Desktop pointer does not work?
If the pointer on your Panasonic Desktop isn't working, ensure the external mouse is connected correctly, if you are using one. Try restarting the computer using the keyboard. If the computer does not respond to keyboard commands, refer to the 'No response' section.
How to fix Panasonic Desktop touch pad input issues?
If you cannot input using the touch pad on your Panasonic Desktop, make sure that [Touch Pad] is set to [Enabled] in the [Main] menu of the Setup Utility. Also, be aware that the drivers for some mice may disable the touch pad, so check your mouse’s operating instructions.
How to fix touchscreen input issues on Panasonic Desktop?
If you cannot input using the touchscreen on your Panasonic Desktop, set [Touchscreen Mode] to [Auto] or [Tablet Mode] in the [Main] menu of the Setup Utility. Also, ensure that [Touchscreen] is set to [Enabled] in the [Advanced] menu of the Setup Utility.
I forgot my Panasonic Desktop password, what can I do?
If you have forgotten your Panasonic Desktop password, contact Panasonic Technical Support. If you have a password reset disk, you can reset the administrator password by setting the disk, entering any wrong password, and following the on-screen instructions to set a new password. If you do not have a password reset disk, reinstall and set up Windows, and then set a new password.
What to do if my Panasonic Desktop won't start and the power indicator is off?
If your Panasonic Desktop isn't starting and the power indicator isn't lit, try these steps: First, connect the AC adapter. If that doesn't work, insert a fully charged battery. You can also try removing the battery pack and AC adapter, then reconnecting them. If devices are connected to the USB port or ExpressCard slot, disconnect them or disable the corresponding settings in the Setup Utility's Advanced menu. Press Fn + F8 to turn off concealed mode. Lastly, check the UEFI Boot setting in the Setup Utility, ensuring it's set to either Enabled or Disabled.
What to do if my Panasonic Desktop shows 'Remove disks or other media. Press any key to restart'?
If your Panasonic Desktop displays the message 'Remove disks or other media. Press any key to restart', it could be due to a floppy disk in the drive without system startup information. Remove the floppy disk and press any key. Also, disconnect any devices connected to the USB port or ExpressCard slot, or disable the [USB Port] or [ExpressCard Slot] in the Setup Utility. If the problem continues after removing the disk, it may indicate a hard disk failure, in this case contact Panasonic Technical Support. As an additional step, you can set [UEFI Boot] to [Disabled] in the [Boot] menu of the Setup Utility.
Why is my Panasonic Desktop Windows startup so slow?
If your Panasonic Desktop experiences slow Windows startup and operation, try pressing F9 in the Setup Utility to reset settings (excluding passwords) to default. Then, restart the Setup Utility and configure your settings again. If you installed resident software after purchasing the computer, try turning it off. Also, disable the pop-up menu and Input Panel Tab by opening the Input Panel, clicking [Tools] - [Options] - [Opening], and removing the check mark from [Show Input Panel sliding open from the tab].
How to fix incorrect date and time on my Panasonic Desktop?
To correct the date and time on your Panasonic Desktop, first, make sure you set the correct settings. If the problem continues, the internal clock battery may need replacement, so contact Panasonic Technical Support. If your computer is connected to a LAN, check the date and time of the server. Note that this computer will not correctly recognize years 2100 A.D. or later.
What to do if my Panasonic Desktop screen is dark?
If your Panasonic Desktop screen is dark, remember that the screen appears darker when the AC adapter is disconnected. Try pressing Fn + F2 to adjust the brightness. Also, press Fn + F8 to turn off the concealed mode.
General| Resolution | 1024 x 768 |
|---|---|
| Touchscreen | Yes |
| Operating System | Windows 7 |
| Rugged Features | MIL-STD-810G certified |
| Graphics | Intel Integrated Graphics |
| Convertible | Yes |
| Ports | USB, Serial, Ethernet, VGA, Headphone/Microphone |
| Wireless | Wi-Fi, Bluetooth |
To Next Page
