Panasonic DMC-FZ70P - Detailed Error Code List

16
3. Error Code List
The error code consists of 8 bits data and it shows the following information.
Attribute Main item Sub item Error code Contents (Upper) Error Indication
High
4bits
Low
4bits
Check point (Lower) Detecting
device
Part/Circuit
LENS Lens drive Focus 18*0 0?01 HP Low detect error
(Focus encoder always detects High, and not becomes
Low)
FOCUS L LENS FPC/
DSP
Mechanical lock, FP9004-(35) signal line or IC6001
(VENUS ENGINE)
0?02 HP High detect error
(Focus encoder always detects Low, and not becomes
High)
FOCUS H
Mechanical lock, FP9004-(35) signal line or IC6001
(VENUS ENGINE)
Zoom 0?10 Collapsible barrel Low detect error
(Collapsible barrel encoder always detects Low.)
ZOOM L ZOOMm/
LENSu
Mechanical lock, FP9004-(24) signal line or IC6001
(VENUS ENGINE)
0?20 Collapsible barrel High detect error
(Collapsible barrel encoder always detects High.)
ZOOM H
Mechanical lock, FP9004-(24) signal line or IC6001
(VENUS ENGINE)
0?30 Zoom motor sensor error (Initialized or Terminated) ZOOM ENC
Mechanical lock, FP9004-(38), (40) signal line or IC6001
(VENUS ENGINE)
0?40 Zoom motor sensor error (During monitor mode.)
Mechanical lock, FP9004-(38), (40) signal line or IC6001
(VENUS ENGINE)
0?50 Zoom motor sensor error (During monitor mode with slow
speed.)
Mechanical lock, FP9004-(38), (40) signal line or IC6001
(VENUS ENGINE)
0?60 Detection of zoom misregistration by impact such as fails (No indication) (No indication)
Lens Unit
OIS 1000 PSD (X) error. Hall element (X axis) position detect error in
OIS unit
OIS X LENSu NG
OIS Unit
2000 PSD (Y) error. Hall element (Y axis) position detect error in
OIS unit
OIS Y
OIS Unit
3000 GYRO (X) error. Gyro (IC7101: X axis) detect error on
Main P.C.B.
GYRO X GYRO NG
IC7101 (Gyro element) or IC6001 (VENUS ENGINE)
4000 GYRO (Y) error. Gyro (IC7101: Y axis) detect error on
Main P.C.B.
GYRO Y
IC7101 (Gyro element) or IC6001 (VENUS ENGINE)
5000 GYRO (R) error. Gyro (IC7101: R axis) detect error on
Main P.C.B.
GYRO R
IC7101 (Gyro element) or IC6001 (VENUS ENGINE)
6000 Drive voltage (X) error OISX REF LENSu/LENS
FPC
LENS Unit, LENS flex breaks, IC6001(VENUS ENGINE)
AD value error, etc.
7000 Drive voltage (Y) error OISY REF
LENS Unit, LENS flex breaks, IC6001(VENUS ENGINE)
AD value error, etc.
8000 OIS GYRO - Digital communication error (No indication) (No indication)
IC7101 (Gyro element) or IC6001 (VENUS ENGINE)
Lens 10*3 0000 Lens cap error (No indication) (No indication)
Zoom motor, Zoom pulse encoder 1, 2
10*4 0000 Lens cap error (During monitor mode)
Zoom motor, Zoom pulse encoder 1, 2
10*8 0000 Lens cap error (During monitor mode with slow speed)
Zoom motor, Zoom pulse encoder 1, 2
18*1 0000 Power ON time out error LENS DRV LENSu
Lens drive system
18*2 0000 Power OFF time out error
Lens drive system