16
RQT9248
Enjoying High Bit rate Audio and Video
This unit supports high bit rate audio (Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution Audio and DTS-HD Master Audio) adopted in
BD-Video.
To enjoy 7.1ch surround sound, the following conditions are necessary. (Part shown in the shaded area of table given below)
NECESSARY CONNECTIONS
≥Connect an amplifier/receiver with 7.1ch speaker.
≥Connect to HDMI AV OUT terminal.
≥HDMI AV OUT terminal: connect an amplifier/receiver supporting HDMI (High Bit rate Audio) using a High Speed HDMI cable (> 7).
NECESSARY SETTINGS
≥Set “BD-Video Secondary Audio” to “Off”. (> 25)
≥HDMI AV OUT terminal: Set “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” to “Bitstream” or “PCM”. (> 25)
Connect an amplifier/receiver (> 7, 8) and confirm the desired audio type and necessary settings (“BD-Video Secondary Audio”, “Dolby D/Dolby
D +/Dolby TrueHD” or “DTS/DTS-HD”).
≥The number of channels listed is the maximum possible number of output channels.
≥Also, depending on the specifications or the settings of the amplifier/receiver, the results of the output may vary.
*1 When the connected equipment is not supported with these audio format, the audio is output as Dolby Digital bitstream, DTS Digital Surround
bitstream or down-mixed 2ch PCM (e.g., TV).
*2 [BD-V]: When playing BD-Video without secondary audio or clicking sound, the audio is output as the same format as if “BD-Video Secondary
Audio” was set to “Off”.
*3 When the connected equipment is not supported with multi channel surround, the audio is output as down-mixed 2ch PCM.
*4 [BD-V]: When the connected equipment is supported with 7.1 channel surround, the audio output is amplified from 5.1ch or 6.1ch to 7.1ch
depending on the DTS, Inc. specifications.
*5 With PCM output, Dolby Digital EX becomes PCM audio decoded as Dolby Digital, DTS-ES recorded to DVD-Video becomes PCM audio
decoded as DTS Digital Surround, and DTS-ES recorded to BD-Video becomes PCM audio decoded as DTS-ES.
*6 [BD-V]: When “BD-Video Secondary Audio” is set to “On”, Dolby Digital EX is output as Dolby Digital and DTS-ES is output as DTS Digital
Surround, however if playing BD-Video without secondary audio or clicking sound, the audio is output as the original format.
NECESSARY SETTINGS
≥HDMI AV OUT/DIGITAL AUDIO OUT terminal: “Digital Audio Output” (> 25)
[Note]
≥When setting “BD-Video Secondary Audio” to “Off”, the clicking sound on the menu and audio with secondary video in picture-in-picture mode
(> 15) cannot be output.
Many BD-Video movie contents are recorded in 24 frames/second in accordance with the film materials. However, they will normally be output in
60 frames/second in accordance with the display format.
These can be output in 24p as the original. Therefore, high-quality video can be enjoyed, such as the improved clarity, enhanced perspective, etc.
NECESSARY CONNECTIONS
≥Connect to a TV supporting 1080/24p input via an HDMI cable.
NECESSARY SETTINGS
≥“24p Output”: “On” (> 26)
Enjoying High Bit rate Audio with 7.1ch speaker
About audio from audio output terminal
Terminal HDMI AV OUT DIGITAL AUDIO OUT
“Dolby D/Dolby D +/Dolby
TrueHD”/
“DTS/DTS-HD”
“Bitstream”*
1
“PCM”*
3
“Bitstream” “PCM”
“BD-Video Secondary
Audio”
“On”*
2
“Off” “On” “Off” “On”/“Off” “On”/“Off”
Dolby Digital/
Dolby Digital EX*
5
Dolby Digital/
Dolby Digital EX*
6
Dolby Digital/
Dolby Digital EX
5.1ch PCM
Dolby Digital/
Dolby Digital EX*
6
Down-mixed 2ch
PCM
Dolby Digital Plus
Dolby Digital
Dolby Digital Plus
5.1ch PCM*
2
7.1ch PCM Dolby Digital
Dolby TrueHD Dolby TrueHD
DTS Digital Surround/
DTS-ES*
5
DTS Digital
Surround/
DTS-ES*
6
DTS Digital
Surround/
DTS-ES
[DVD-V]: 5.1ch PCM DTS Digital
Surround/
DTS-ES*
6
[BD-V]: 7.1ch PCM*
4
DTS-HD High Resolution
Audio
DTS Digital
Surround
DTS-HD High
Resolution Audio
7.1ch PCM*
4
DTS Digital
Surround
DTS-HD Master Audio
DTS-HD Master
Audio
7.1ch LPCM
Down-mixed
5.1ch PCM
7.1ch PCM
Down-mixed
5.1ch PCM*
2
7.1ch PCM
Down-mixed 2ch
PCM
Regarding 24p output
DMP-BD35GT&GN-RQT9256_eng.book 16 ページ ２００８年９月２４日 水曜日 午後５時５分
To Next Page
Loading...
