30
RQT9248
TV screen and video (continued) Page
Sound
HDMI connections
Video is not output in high
definition.
≥High definition video cannot be output through the VIDEO OUT terminal.
≥Confirm that the “HDMI Video Mode”, “HDMI Video Format”, and “Component Resolution” in
the Setup menu are set properly.
≥
The video output resolution is restricted to “576p/480p” when
DVD-Video discs and
BD-Video discs
recorded at a rate of 50 field per second are output from the COMPONENT VIDEO OUT terminals.
—
26
—
Status messages do not appear.
≥Select “Automatic” in “On-Screen Messages” in the Setup menu. 25
The 4:3 aspect ratio picture
expands left and right.
Screen size is wrong.
≥Use the television to change the aspect. Refer to your television’s operating instructions.
≥When using a component video cable, set “Progressive” to “Video”. If the situation is not
restored after that, set “TV Aspect” to “4:3 Pan & Scan”.
—
23, 26
There is a lot of after-image
when playing video.
≥Turn “3D NR” or “Integrated NR” off if it is on.
23
There is no apparent change in
picture quality when adjusted
with the “Picture” menu in the
on-screen menu.
≥The effect is less perceivable with some types of video.
—
The masked-off area is masked
in gray.
≥If the “Screen Saver Function” in the Setup menu is set to “Off”, the masked-off area is
displayed in black.
25
Still pictures (JPEG) do not
playback normally.
≥The images that were edited on the PC, such as Progressive JPEG, etc., may not playback.
20
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio
type.
≥Check the connections and the “Digital Audio Output” settings. Check the input mode on the
amplifier/receiver if you have connected one.
≥Press [AUDIO] to select the audio.
≥Turn off “V. Surround” in the following cases.
– When using discs that do not have surround sound effects such as Karaoke discs.
– When playing bilingual broadcast programs.
≥The sound effects (Re-master, V. Surround, etc.) will not work when the bitstream signal is
output from the HDMI AV OUT terminal or the DIGITAL AUDIO OUT terminal.
6–8, 25
14
23
—
Cannot switch audio. ≥There are discs for which audio cannot be changed because of how the disc was created.
≥When connecting an amplifier/receiver using a optical digital audio cable or an HDMI cable,
you cannot switch the audio if “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” is set to
“Bitstream”. Set “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” to “PCM” or connect
using AUDIO OUT terminal.
—
7, 8, 25
The images from this unit do
not appear on the television.
Picture is distorted.
Jittering occurs.
≥Press [∫] and [1] (PLAY) simultaneously on the unit for more than 5 seconds to shift to more
compatible mode with HDMI equipment. However, Dolby Digital Plus, Dolby TrueHD, and
DTS-HD audio are not output in bitstream. To output the bitstream, select “Default Settings”
to restore the factory presets and make proper settings.
≥To output video from a device connected with an HDMI cable, set “HDMI Video Mode” to “On”
in the Setup menu.
≥Picture may not be seen when more than 4 devices are connected with HDMI cables.
Reduce the number of connected devices.
≥When “24p Output” is set to “On”, HDMI authentication takes place where 24p images switch
to other images, and a black screen is displayed.
≥When “24p Output” is set to “On”, jittering may occur while playing DVD-Video. In this case,
turn “24p Output” to “Off”.
27
26
—
26
26
The 4:3 aspect ratio picture
expands left and right.
Screen size is wrong.
≥Change “TV Aspect” type to “16:9”.
26
When playing DVD-Video using
progressive output, one part of
the picture momentarily
appears to be doubled up.
≥When you use the HDMI AV OUT terminal for video output, follow the steps below for setting.
1 Connect this unit to the TV with any cable except the HDMI cable.
2 When you connect with the Component Video cable, set “HDMI Video Mode” to “Off” and
“Component Resolution” to “576i/480i” in the Setup menu.
26
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio
type.
≥Audio may not be heard when more than 4 devices are connected with HDMI cables.
Reduce the number of connected devices.
≥The sound effects will not work when the bitstream signal is output from the HDMI AV OUT
terminal or the DIGITAL AUDIO OUT terminal.
≥To output audio from a device connected with an HDMI cable, set “HDMI Audio Output” to
“On” in the Setup menu.
≥Depending on the connected equipment, the sound may be distorted if this unit is connected
with an HDMI cable.
≥When “BD-Video Secondary Audio” is set to “On”, Dolby Digital Plus, Dolby TrueHD, and
DTS-HD are converted to 48 kHz Dolby Digital or DTS Digital Surround and output. LPCM
7.1 channel audio is converted to 5.1 channel audio. In this case, set the “BD-Video
Secondary Audio” to “Off”.
—
—
26
—
25
DMP-BD35GT&GN-RQT9256_eng.book 30 ページ ２００８年９月２４日 水曜日 午後５時５分
To Next Page
Loading...
