Reference
31
SQT0099
The remote control does not work properly.
¾ Change the batteries in the remote control.
(> 5)
¾ The remote control and this unit are using
different codes.
Press and hold [OK] and the displayed
number (“”) for more than 5 seconds.
The TV tuner mode is not displayed when the
TV is turned on.
¾ This phenomenon may occur, depending on
the TV setting, when “Quick Start” is set to
“On”.
¾ Depending on the TV, this phenomenon may
be prevented by reconnecting the HDMI cable
to a different HDMI input terminal or by
changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
¾ The ratings level returns to the factory
defaults.
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
4 Press [OK].
The TV screen turns black.
¾ In the following cases, HDMI authentication
takes place and a black screen is displayed:
– When “24p(4K)/24p Output” is set to
“24p(4K)” or “24p”.
– When the display is switched between 2D
and 3D images.
– [BDT460] When you quit the 4K playback of a
still picture by displaying another screen,
including the Home menu.
This unit does not recognize the USB
connection correctly.
¾ Disconnect and re-connect the USB cable. If
it still does not recognize the connection, turn
this unit off and on again.
¾ USB devices may not be recognized by this
unit when connected using the following :
– a USB hub
¾ If you connect USB HDD to this unit, use the
USB cable that is supplied with the HDD.
[For[t he [ Unit e d[ K ingdom,[Ireland[a nd[ South[East[Asi a ]
¾ When you connect a USB HDD, use the right
USB port (USB2). (> 14)
The images from this unit do not appear on
the TV.
Picture is distorted.
¾ An incorrect resolution is selected in “HDMI
Video Format”. Reset the setting as follows:
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
Set the item again. (> 26)
– When Dolby Digital Plus, Dolby TrueHD,
and DTS-HD
®
audio are not output properly,
select “Yes” in “Default Settings” (> 30) and
make proper settings.
¾ The unit and TV are using different video
systems.
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
– “00 RET” is displayed on the unit’s display.
3 Press [1] (right) repeatedly on the remote
control until “05 P/N” is displayed on the unit’s
display.
4 Press and hold [OK] for more than 5 seconds.
The system switches from PAL to NTSC or
vice versa.
If “SET ” is displayed on the unit’s display
when a button is pressed on the remote
control, change the code on the remote
control.
– “00 RET” is displayed on the unit’s display.
3 Press [1] (right) repeatedly on the remote
control until “03 VL” is displayed on the unit’s
display.
– a USB extension cable
Picture
– “00 RET” is displayed on the unit’s display.
3 Press [1] (right) repeatedly on the remote
control until “04 PRG” is displayed on the
unit’s display.
4 Press and hold [OK] for more than
5 seconds.
Settings
DMP-BDT460&360_EBGNGA-SQT0099.book 31 ページ ２０１４年１月２８日 火曜日 午後３時５７分
To Next Page
Loading...
