EasyManua.ls Logo

Panasonic ER153 - Specifications

Panasonic ER153
16 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
cleaning
hook
to
open
the
blade
in
order
to
remove
hair
which
may
be
caught
between
the
blades.
(See
Fig.
5)
Lubricate
the
space
between
the
stationary
and
mov-
ing
blades
with
2
or
3
drops
of
oil
after
every
few
uses.
To
reassemble,
First,
set
the
dial
(D)
to
“3”,
and
reverse
the
above
procedure,
pushing
the
blade
block
until
it
clicks
firmly
into
position.
(See
Fig.
6)
Special
attention
when
charging
e
If
the
clipper
is
not
used
for
an
extended
period,
charge
every
six
months
to
preserve
battery
life.
e
Avoid
charging
the
battery
at
temper-
atures
below
0°C
or
above
40°C.
e
Avoid
charging
the
battery
in
direct
sun-
light
or
near
a
radiating
heat
source.
Caution:
e
Clean
the
housing
using
only
a
cloth
slightly
dampened
with
water
or
a
mild
soap
solution.
è
Never
use
a
caustic
solution.
e
Never
submerge
the
hair
clipper
in
water.
e
Keep
out
of
the
reach
of
children.
e
Do
not
use
to
trim
the
hair
of
a
pet.
e
The
hair
clipper
may
become
warm
during
operation
and/or
charging.
This
is
normal.
e
Avoid
grabbing
the
hair
clipper
by
the
power
cord,
as
it
may
become
detached,
causing
damage
or
injury.
e
Never
tamper
with
moving
parts.
e
|f
the
hair
clipper
is
not
working
prop-
erly,
have
it
inspected
at
an
autho-
rized
service
center.
e
Use
the
ER153
hair
ctipper
with
the
RE5-66
adapter
only.
Note:
The
Supply
cord
of
the
charging
adaptor
RE5-66
cannot
be
replaced;
if
the
cord
is
damaged,
the
appliance
should
be
discarded.
ATTENTION:
A
nickel
cadmium
battery
that
is
recyclable
powers
the
product
you
have
purchased.
At
the
end
of
its
useful
life,
under
vari-
ous
state
and
local
laws,
it
is
illegal
to
dispose
of
this
battery
into
your
munici-
pal
waste
stream.
Please
call
1-800-8-BATTERY
for
infor-
mation
on
how
to
recycle
this
battery.
How
to
remove
the
built-in
rechargeable
batteries
before
disposal
of
the
clipper
The
batteries
in
this
clipper
are
not
intendetd
to
be
replaced.
The
procedure
described
in
fig.
7,
Bis
intended
only
for
the
purpose
of
proper:
disposal.
Discard
the
clipper
after
the
batteries
have
been
removed.
WARNING:
Do
not
attempt
to
replace
the
batteries
for
the
purpose
of
reusing
the
clipper.
This
could
result
in
the
risk
of
fire.
.
Remove
the
attachment
and
blade
block.
.
Remove
the
three
screws
and
open
the
housing.
.
Remove
the
motor
and
circuit
board.
.
Insert
a
screwdriver
as
shown
in
the
illustration
and
remove
the
battery.
(Fig.
7,
8)
BE
D
—
Specifications
Power
source:
120V
AC,
60Hz
Motor
voltage:
2.4V
DC
Charging
time:
8
hours

Table of Contents

Related product manuals