Why Panasonic MCO-170AICUVHL chamber temperature does not match the set value?
If the chamber temperature on your Panasonic Incubator isn't matching the set value, check if the ambient temperature is less than 5 ?C different from the set chamber temperature. Also, make sure the outer door is closed and the inner door isn't left open. Lastly, ensure the incubator isn't near equipment that generates electromagnetic waves.
What to do if Panasonic MCO-170AICUVHL CO gas density does not match the set value?
If the CO gas density in your Panasonic Incubator isn't matching the set value, verify that the secondary pressure for the gas regulator is at the specified value of 0.03 MPa(G) (0.3 kgf/cm2(G), 4.3 psi(G)). Check for any blockages in the gas tube and ensure the duct is securely attached to the 4 points hooks. Also, confirm that the fan is properly attached and pushed all the way to the motor shaft. Finally, ensure the incubator is not operating near equipment that generates electromagnetic waves.
What to do if Panasonic MCO-170AICUVHL Incubator CO gas density is slow to recover?
If the CO gas density is slow to recover in your Panasonic Incubator, and the CO gas pressure is normal, the HEPA filter may be clogged and you should contact our sales representative or agent. Also, check if there is little gas remaining in the CO gas cylinder and ensure the secondary pressure for the gas regulator is at the specified value of 0.03 MPa(G) (0.3 kgf/cm2(G), 4.3 psi(G)). Check for blockages in the gas tube and ensure the duct is securely attached to the 4 points hooks. Confirm that the fan is properly attached and pushed all the way to the motor shaft.
What to do if Panasonic Incubator is consuming a large quantity of CO gas?
If your Panasonic Incubator is consuming a large quantity of CO gas, check if the outer and inner doors are being frequently opened and closed. Inspect connectors for gas leaks due to deterioration of the gas tube or pinhole leaks; consider replacing the gas tube annually. Also, verify if the packing seal for the inner door is defective and if the access hole is open.
What to do if Panasonic MCO-170AICUVHL chamber humidity does not rise?
If the chamber humidity in your Panasonic Incubator isn't rising, ensure there is enough sterile distilled water in the humidifying pan.
Why normal cultures are not possible, and the CO gas density is suspect in Panasonic MCO-170AICUVHL Incubator?
If normal cultures are not possible and the CO gas density is suspect in your Panasonic Incubator, check if the ambient air environment around the incubator is normal and if there is a source of polluted gas nearby.
What to do if Panasonic MCO-170AICUVHL does not operate at all?
If your Panasonic Incubator isn't operating, check if it's properly plugged in and if there's a power outage or a tripped circuit breaker. Also, verify that the removal power supply cord is connected to the port on the lower right side of the cabinet.
Why Panasonic Incubator outer door does not open?
If the outer door of your Panasonic Incubator doesn't open, it may be because the electric lock is engaged when the power switch is OFF. Turn the power switch ON or use the accessory unlock key to override the electric lock. Also, the outer door is electrically locked during decontamination.
Why CO gas is not being injected in Panasonic MCO-170AICUVHL?
The CO control method for the Panasonic Incubator is the ON-OFF method. CO gas is intermittently injected as the gas density in the chamber approaches the set value. Injections may be stopped for periods of approximately 15 seconds, but that is not an error. The gas is not injected until the temperature of the CO sensor becomes stable enough approx. 1 hour, after turning ON the power switch or recovering from power failure.
Why Panasonic Incubator UV lamp lights when the outer door is open?
If the UV lamp lights when the outer door of your Panasonic Incubator is open, check if something is pushing the door switch.
Explains hazard symbols (WARNING, CAUTION) and fundamental safety advice.
Details precautions for electrical safety, grounding, and proper installation environment.
Covers safe handling procedures, maintenance, storage, and disposal advice.
Specifies the necessary environmental conditions and location characteristics for installation.
Outlines the procedure for physically installing the unit, including leveling and grounding.
Details the safe and correct procedure for connecting the CO2 gas cylinder.
Details how to input numerical values and set chamber temperature and CO2 density.
Explains how to configure automatic temperature and CO2 density alarm thresholds.
Details settings for alarm delay, ring back function, and remote alarm output.
Details the step-by-step procedure for chamber decontamination using H2O2.
General| Type | CO2 Incubator |
|---|---|
| Temperature Control Range | 5°C above ambient to 50°C |
| Temperature Stability | ±0.1°C |
| CO2 Control Range | 0 to 20% |
| CO2 Stability | ±0.1% |
| Capacity | 170L |
| Internal Volume | 170 L |
| Chamber Volume | 170 L |
| UV Sterilization | Yes |
| Temperature Range | 5°C above ambient to 50°C |
| Temperature Uniformity | ±0.3°C |
| CO2 Accuracy | ±0.15% |
| CO2 Sensor Type | Infrared CO2 Sensor |
| Humidity Range | 95% RH at 37°C |
| Shelves | 3 |
| Power Supply | AC 230V, 50/60Hz |
| Humidity | 95% RH at 37°C |
To Next Page