Panasonic MJ-J176PWTC

Questions and Answers

D
Douglas SmithAug 18, 2025
How to fix noise and vibration in Panasonic MJ-J176PWTC?
- D
  Donald SmithAug 18, 2025
  If your Panasonic Juicer experiences unusual noise and vibration, check these potential causes: * Deformation of spinner: Replace the spinner. * Residue has collected unevenly: Clean the spinner. * Incompletely fastened clasp: Fasten it completely. * The fastening part of the container cover clasp is worn out: Replace the cover. * Incompletely fastened back cover: Fasten it completely. * Incorrect placement of the main unit: Inspect the rubber feet. Use on a level surface.
A
Abigail WhiteAug 20, 2025
Why does my Panasonic MJ-J176PWTC Juicer juice contain too much residue?
- K
  Kathryn JacksonAug 20, 2025
  If your Panasonic Juicer is producing juice with too much residue, it could be due to a worn-out cutter blade. In this case, replace the complete spinner. Another cause might be a gap between the inlet bottom and cutter blade that is too large. To fix this, use two or three adjusting washers on the motor shaft.
A
awilsonAug 22, 2025
What to do if my Panasonic MJ-J176PWTC Juicer motor overheats?
- B
  Brittany ShawAug 22, 2025
  If the motor of your Panasonic Juicer overheats, there are several potential causes: * High voltage: Adjust it. * Shorted motor: Replace the motor. * Eccentric main shaft gear part: Replace the part. * Main shaft is hard to operate: Disassemble and adjust it or replace it. * Unloaded operation: Be sure that something is in the container before operating. * Overload (rotation is impeded by a hard object, or a high viscosity sub- stance in the container): Refer to operation.
D
Deborah LevyAug 26, 2025
Why is my Panasonic MJ-J176PWTC Juicer leaking juice?
- M
  Mario BrooksAug 26, 2025
  If juice is leaking from your Panasonic Juicer, it may be due to several reasons: * Container and/or cover deformed or broken: Replace the container or cover. * Incorrect clasp fastening: Examine the clasp; adjust the fastening force. * Foreign materials are clogged between the container cover and the container: Clean it and remove them. * Excessive vibration: Clean it and adjust the spinner balance.
L
Larry GreenAug 28, 2025
What to do if Panasonic MJ-J176PWTC motor rotates but cutter doesn't?
- L
  Leonard MccartyAug 28, 2025
  If your Panasonic Juicer's motor rotates, but the cutter doesn’t, it's likely that the gear is worn out. To resolve this, replace the cutter base gear.
R
Rachel Orr MDAug 30, 2025
How to stop Panasonic Juicer juice leakage?
- S
  Stephanie SantosAug 30, 2025
  If you are experiencing juice leakage with your Panasonic Juicer, check for these potential causes: * Broken container: Replace the container. * Bad container base: Replace the packing. * Loose fastened part: Fasten it tightly. * Main shaft is worn out: Replace the main shaft and bearing.
O
oliviasheaSep 1, 2025
Why does the cutter rub against the inlet bottom of my Panasonic MJ-J176PWTC Juicer?
- S
  Shawn LopezSep 1, 2025
  If the cutter rubs against the inlet bottom of your Panasonic Juicer, it could be caused by: * Gear incompletely engaged between cutter base and spinner: Engage the gear. * Too many adjustment rings on the motor shaft: Decrease the number of adjustment rings and adjust the gap within the range of 0.5 - 0.9mm.
J
Jeffrey DunnSep 4, 2025
Why doesn't my Panasonic MJ-J176PWTC Juicer motor rotate?
- N
  Nicholas DurhamSep 4, 2025
  If your Panasonic Juicer's motor doesn’t rotate, it could be due to: * Switch malfunction: Replace the switch. * Cord cut or disconnected: Replace the cord.
M
Mr. Brian Cabrera MDSep 7, 2025
How to fix poorly extracted juice from Panasonic MJ-J176PWTC?
- O
  ogarrettSep 7, 2025
  If your Panasonic Juicer is not extracting juice well, it could be due to several reasons: * Cutter doesn’t operate well: Replace complete spinner. * Spinner is broken: Replace complete spinner. * Continuous use for a long period: Remove the residue. * Too large a gap between inlet bottom and cutter blade: Adjust it within the range of 0.5 - 0.9mm.
W
williamshawSep 9, 2025
What does it mean if my Panasonic Juicer motor roars but doesn't rotate?
- M
  Mike SmithSep 9, 2025
  If your Panasonic Juicer motor “roars” but doesn’t rotate, ensure you switch it off immediately. This could be due to motor bearing rushed. Disassemble and apply oil, or replace the motor.

Summary

2 Specifications

2.1 MJ-J176 PWTC

Lists detailed specifications for the MJ-J176PWTC model.

3 Location of Controls and Components

4 Operating Instructions

4.1 How to use

Detailed guide on how to operate the juicer and blender modes correctly.

4.2 Safety

Explains circuit breaker protection and safety lock mechanisms to prevent hazards.

4.3 How to Clean

Instructions for cleaning the juicer, blender, and dry mill components.

5 Troubleshooting Guide

5.1 The Juicer, the Blender commons

Troubleshooting common issues applicable to both juicer and blender functions.

5.2 The Juicer

Specific troubleshooting steps for problems encountered with the juicer function.

5.2.3 Spinner Difficult to Install and Remove

Addresses difficulties in installing or removing the spinner component.

5.2.4 Juice is Poorly Extracted

Troubleshooting steps for poor juice extraction performance.

5.2.5 Juice Contains Too Much Residue

Solutions for juice containing excessive residue.

5.2.6 Cutter Rubs Against Inlet Bottom

Diagnosing and resolving issues where the cutter rubs against the inlet bottom.

5.2.7 Leakage of Juice

Troubleshooting steps for juice leakage problems.

5.3 The Blender

5.3.1 Cutter Wont Rotate

Resolving issues where the blender's cutter fails to rotate.

5.3.2 Motor Rotates but Cutter Doesnt Rotate

Troubleshooting when the motor runs but the cutter does not.

5.3.3 Noise, Vibration

Addressing noise and vibration problems during blender operation.

5.3.4 Juice Leakage

Troubleshooting juice leakage issues specific to the blender.

6 Disassembly and Assembly Instructions

6.1 Coupler

Instructions for removing and replacing the coupler component.

6.2 Bottom Plate and Motor

Procedure for detaching the bottom plate and motor assembly.

6.3 Carbon Brush

Steps for removing and replacing the carbon brush.

6.4 Power Cord

Instructions for replacing the power cord.

6.5 Clamps A and B

Procedure for removing and replacing clamps A and B.

6.6 Switch, Switch Plate

Steps for removing and replacing the switch and switch plate.

6.8 Glass Container and Cutting Blade

6.9 Mill Container and Mill Cutter

7 Wiring Connection Diagram

7.1 Schematic Diagram

Provides the electrical schematic diagram of the appliance's internal wiring.

7.2 Basic Wiring Diagram

Shows the basic layout of the wiring connections within the appliance.

8 Exploded View and Replacement Parts List

8.1.1 Parts Location

Diagram illustrating the location of all parts for the MJ-J176PWTC model.

8.1.2 Replacement Parts List

Detailed list of all replaceable parts with part numbers and descriptions.

8.1.3 Packing Instruction

Details the procedure for packing the product for shipment.

Summary

2 Specifications

2.1 MJ-J176 PWTC

Lists detailed specifications for the MJ-J176PWTC model.

3 Location of Controls and Components

4 Operating Instructions

4.1 How to use

Detailed guide on how to operate the juicer and blender modes correctly.

4.2 Safety

Explains circuit breaker protection and safety lock mechanisms to prevent hazards.

4.3 How to Clean

Instructions for cleaning the juicer, blender, and dry mill components.

5 Troubleshooting Guide

5.1 The Juicer, the Blender commons

Troubleshooting common issues applicable to both juicer and blender functions.

5.2 The Juicer

Specific troubleshooting steps for problems encountered with the juicer function.

5.2.3 Spinner Difficult to Install and Remove

Addresses difficulties in installing or removing the spinner component.

5.2.4 Juice is Poorly Extracted

Troubleshooting steps for poor juice extraction performance.

5.2.5 Juice Contains Too Much Residue

Solutions for juice containing excessive residue.

5.2.6 Cutter Rubs Against Inlet Bottom

Diagnosing and resolving issues where the cutter rubs against the inlet bottom.

5.2.7 Leakage of Juice

Troubleshooting steps for juice leakage problems.

5.3 The Blender

5.3.1 Cutter Wont Rotate

Resolving issues where the blender's cutter fails to rotate.

5.3.2 Motor Rotates but Cutter Doesnt Rotate

Troubleshooting when the motor runs but the cutter does not.

5.3.3 Noise, Vibration

Addressing noise and vibration problems during blender operation.

5.3.4 Juice Leakage

Troubleshooting juice leakage issues specific to the blender.

6 Disassembly and Assembly Instructions

6.1 Coupler

Instructions for removing and replacing the coupler component.

6.2 Bottom Plate and Motor

Procedure for detaching the bottom plate and motor assembly.

6.3 Carbon Brush

Steps for removing and replacing the carbon brush.

6.4 Power Cord

Instructions for replacing the power cord.

6.5 Clamps A and B

Procedure for removing and replacing clamps A and B.

6.6 Switch, Switch Plate

Steps for removing and replacing the switch and switch plate.

6.8 Glass Container and Cutting Blade

6.9 Mill Container and Mill Cutter

7 Wiring Connection Diagram

7.1 Schematic Diagram

Provides the electrical schematic diagram of the appliance's internal wiring.

7.2 Basic Wiring Diagram

Shows the basic layout of the wiring connections within the appliance.

8 Exploded View and Replacement Parts List

8.1.1 Parts Location

Diagram illustrating the location of all parts for the MJ-J176PWTC model.

8.1.2 Replacement Parts List

Detailed list of all replaceable parts with part numbers and descriptions.

8.1.3 Packing Instruction

Details the procedure for packing the product for shipment.

The Panasonic MJ-J176PWTC is a versatile kitchen appliance designed to function as both a juicer and a blender, with an additional dry mill attachment for grinding. This multi-functional device is intended for domestic use, offering a range of features for preparing various food and beverage items.

Function Description

The primary function of the MJ-J176PWTC is to extract juice from fruits and vegetables, blend ingredients for smoothies and purees, and grind dry items like spices or nuts.

Juicer Function: This mode is designed for extracting fresh juice. It features a feeder opening where ingredients are introduced, a spinner that separates pulp from juice, and a spout for dispensing the extracted liquid. The juicer is suitable for a variety of fruits and vegetables, allowing users to create fresh, healthy beverages.
Blender Function: The blender attachment is used for mixing, pureeing, and liquefying ingredients. It comes with a container and cutting blades, ideal for making smoothies, soups, sauces, and other blended concoctions. The blender is capable of handling both soft and semi-solid ingredients when combined with liquids.
Dry Mill Function: This specialized attachment is for grinding dry ingredients. It includes a mill container and cutting blades designed to process items like coffee beans, spices, or nuts into a fine powder or coarse consistency.

Usage Features

The MJ-J176PWTC incorporates several features to enhance user experience and ensure safe operation.

Control Panel: The device is equipped with a switch panel that allows users to select between different operating modes and speeds. For the juicer, there's an ON/OFF push button. The blender offers two speed push buttons and a pulse function, providing greater control over blending consistency. The pulse function is particularly useful for short bursts of power, ideal for chopping or achieving specific textures.
Safety Lock Mechanism: A crucial safety feature is the integrated safety lock. This mechanism prevents the motor from operating if the juicer container, blender container, or dry mill container is not properly attached and locked into place on the motor housing. This ensures that the cutting blades are securely housed before operation, minimizing the risk of accidental injury. Users must ensure the clamps are locked for the juicer and twist the blender/dry mill container clockwise until it locks.
Food Pusher: For the juicer function, a food pusher is provided to safely guide ingredients into the feeder opening and towards the spinner, preventing direct contact with the rotating parts.
Container Design: The juicer container, blender container, and dry mill container are designed for easy attachment and removal. The blender container includes a gasket to prevent leakage during operation.
Overload Protection: The appliance is equipped with a circuit breaker protection system. In case of motor overloading, the circuit breaker automatically stops the motor to prevent damage. If this occurs, users are instructed to press the "0" (off) button, remove any food residue, cut ingredients into smaller pieces, or reduce the quantity of ingredients before resuming operation. This protects the motor from excessive strain and prolongs the device's lifespan.
Ingredient Handling Guidelines: Specific guidelines are provided for optimal use of each function. For blending, users are advised against crushing ice cubes alone, to dice solid foods first, and to blend with liquid. Continuous operation of the blender is limited to 3 minutes, with a recommended 1-minute stop before resuming. For juicing, soft fruits that produce a puree (like bananas or peaches) are not recommended as they can clog the spinner. Users are also advised to empty the container when food residue accumulates to prevent malfunction or contamination of the juice. For dry milling, wet ingredients, liquids, or hard solid ingredients like turmeric are prohibited, and operation is limited to 60 seconds at a time.

Maintenance Features

Regular cleaning and proper maintenance are essential for the longevity and hygienic operation of the MJ-J176PWTC.

Cleaning Brush: A dedicated cleaning brush is included to facilitate the cleaning of intricate parts, especially the spinner and cutting blades of the juicer.
Detachable Components: Most components, including the juicer container, spinner, blender container, cutting blades, dry mill container, and mill cutter, are detachable for thorough cleaning. This allows users to access all surfaces that come into contact with food.
Cleaning Instructions: Detailed cleaning instructions are provided for each part. Users are advised to unplug the device before cleaning, handle sharp cutting blades carefully, and use cold or lukewarm water with a soft sponge. Abrasive materials, steel wool pads, benzene, thinner, or alcohol are explicitly prohibited for cleaning to prevent damage to the appliance. Dishwasher use is also not recommended for certain parts.
Disassembly and Assembly: The manual provides step-by-step instructions for disassembling and assembling key components such as the coupler, bottom plate, motor, carbon brush, clamps, switch, glass container, and mill container. This allows for deeper cleaning, part replacement, or troubleshooting. For example, the cutting blade of the blender and mill can be removed by wrapping it with a cloth for protection and using long nose pliers to turn the upper connector.
Clearance Adjustment: For the juicer, instructions are provided for adjusting the clearance between the upper cutter surface of the spinner and the bottom of the feeder opening. This adjustment, using a clearance gauge, ensures optimal juice extraction and prevents rubbing, which could lead to wear or damage.
Troubleshooting Guide: A comprehensive troubleshooting guide is included, addressing common issues such as the motor not rotating, overheating, unusual odors, noise, vibration, difficulty installing/removing the spinner, poor juice extraction, excessive residue in juice, cutter rubbing, and juice leakage. This guide helps users identify the cause of a problem and provides remedies, often involving cleaning, adjustment, or part replacement.
Part Replacement: The manual includes an exploded view and a replacement parts list, identifying components with special safety characteristics marked with a triangle. Users are instructed to use only manufacturer-specified parts when replacing these critical components to maintain safety and performance.
Stain Removal: Specific advice is given for removing stains, such as orange juice stains, which can be cleaned using alcohol or detergent, while still cautioning against volatile substances.
Water Temperature: Users are warned not to clean parts with boiling water or attempt to dry parts quickly with fire, emphasizing gentle and safe cleaning practices.