119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
INN. BATT/EXT. BATT Detect
Test SW
Dew Detect
Tape Take-up Photo Sensor Detect
Tape Supply Photo Sensor Detect
Contact ID Detect 3
Contact ID Detect 2
Contact ID Detect 1
Voltage Reference
Voltage
Voltage
GND
Camera Reset
B CLK
Data Complete for EXT-memory Mode
(N.C.)
Address Latch Enable for EXT-Memory Mode
Read Strobe for EXT-Memory Mode
Byte Low Write for EXT-Memory Mode
INN BATT H
TEST
T PHOT
S PHOT
DEW
MIC AD3
MIC AD2
MIC AD1
A VREF
A VCC
VCC2
VSS
CAM RST
BCLK
DC
PO3/RW
ALE
RD
BLW
–
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
–
–
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
NC
DT15
ADDT14
ADDT13
ADDT12
ADDT11
ADDT10
ADDT9
ADDT8
ADDT7
ADDT6
ADDT5
ADDT4
ADDT3
ADDT2
ADDT1
ADDT0
VSS
VCC2
I
I
I
I
I
I
I
I
–
–
–
–
O
O
I
O
O
O
O
(N.C.)
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
EXT-Memory Address/Data BUS
GND
Voltage
PIN.
NO.
IC2011 (D784037GK524): RS-232C INTERFACE MICROCOMPUTER
SIGNAL
NAME
I/O EXPLANATION
1 EVR SCK O
Serial Clock Signal for SYNC Serial
Communication (To Camera Micom)
2 EVR SBO O
Serial Data Signal for SYNC Serial
Communication (To Camera Micom)
5 VTR T O
SYNC Serial Communication Enable
Signal for Camera Micom
17 INSEL
–
(N.C.)
7 RESET I Reset Signal
8 VDD
–
VDD ( {3V )
9 X2
O
Oscillator (14.7456MHz)
10 X1 I Oscillator (14.7456MHz)
11 VSS
–
GND
12
S TITLE L
O Sound Effect Control Signal
13 L/R CONT O LCD Driver Control (L
/
R Invert)
14 U/D CONT O LCD Driver Control (U
/
D Invert)
15 LCD P SAVE
–
(N.C.)
18 TALLY O TALLY LED Control
19
A LINE H
–
(N.C.)
20 T PH AD2 O Take u
21 T PH AD1 O Take u
22 S PH AD2 O Supply Tape Sensor
23 S PH AD1 O Supply Tape Sensor
24 EYE P SAVE
–
(N.C.)
25 LCD WIDE O LCD Driver Wide Select
26
SPK ON L
O Speaker ON
27
WIDNSW H
O Noise Silent
28 VTR LED O VTR Mode LED
29 CAM LED O CAMERA Mode LED
30
VCO H
O
VCO Test Mode H
31
LCD BL CONT
O LCD Back Light Control Signal
32
BL BRIGHT H
O Back Light Bright Control Signal
33
EVF BL CONT
O EVF Back Light Control Signal
34
EVF ONH
O EVF ON
35
LCD ON H
O LCD ON
PIN.
NO.
SIGNAL
NAME
I/O EXPLANATION
46 TEST
–
GND
47 CGCS O CG CS
48 CGPCL O CG PCL
50 UARTI I RS-232C Data
51 UARTO O RS-232C Data
52 PCOE O RS-232C Driver Output Enable
53 BACK RST
–
(N.C.)
54 TEST0 I
VTR Test Signal
(H: Normal, L: Test Mode)
55 VDD
–
VDD ( {3V)
56 PC RST I Reset Signal Detect (AD Input)
60 STBY I RS-232C Cable Connect Confirm
64 AVDD
–
Voltage for AD Converter ( {3V)
65 AVREF1
–
Reference Voltage for AD Converter
( {3V)
66 AVSS
–
GND for AD Converter
69 AVREF2
–
GND
70 AVREF3
–
GND
71 NM1
–
GND
72 CAM T I
Camera Service
/
232C Micom Select
Signal (H: 232C, L: Camera Service)
73 FRP I Frame SYNC Signal
76 SCK I
Serial Clock Signal for SYNC Serial
Communication (To VTR Micom)
77 COM RDI I
SYNC Serial Communication Enable
Signal for VTR Micom
78 EVR SBI I
Serial Data Input for SYNC Serial
Communication (To Camera Micom)
79 SDI I
Serial Data for SYNC Serial
Communication (To VTR Micom)
80 SDO O
Serial Data for SYNC Serial
Communication (To VTR Micom)
61 BACK DET
–
GND
45 VSS
–
GND
38 S TITLE RST O
36 S TITLE DI O
37 S TITLE CI O
EXPLANATION
PIN.
NO.
SIGNAL
NAME
I/O EXPLANATION
PIN.
NO.
SIGNAL
NAME
I/O
To Next Page
Loading...
