Special VCR Features
Channel Caption
You can set channel names, i.e. ABC,
CBS, so that when selected, the
channel name and number appear on-
screen for easy identification.You can
go with preset names (up to 24), or
manuallycreate your own (up to 10).
Note: You will need a list of channels
received in your area and the channel
numbersyou receivethem on.
Preset Caption
1Press ACTION to display the MAIN
MENU.
2 Press &Y4• to select"CH," and
then press ACTION to display the
SET UP CHANNEL screen.
3 Press AV to select"CHANNEL
CAPTION,"and then press • todisplay
the CHANNELCAPTIONscreen.
MAIN
.... SET UP CHANNEL ....
ANTENNA : CABLE
SELECT:& • KEY
SET :=. KEY
END :ACTION KEY
!
a
e
DD
DELETE
2
?
4
5
a
b
c
d
A
LI_Press AT toselect"PRESET
CAPTION," and then press• to display
thePRESET CAPTIONscreen.
• You can set up to twenty-four channel
captions. If you want to set a station
name other than these, go to the "Manual
Caption" section below.
5 Press • to move the shaded area
to the right side.
Then, press A_' to change the
CHANNEL CAPTION ---
_l=JaZi=_'i=l
MANUAL CJ_P'I"tON
.... PRESET CAPTION ....
M "" PBS --
CBS -- CNN --
FOX -- ESPN --
NBC -- HBO --
SELECT :• • KEY
SET :I_ KEY
END :ACTION KEY
memorized channel number to [.... PRESETCAPTION.... l
match the caption. T_r 42 cBc s2 I
Next, press • to set the memorized [ uPN -- cm 21 I
WB 35 TBN 52 I
channel number. _sc -- _.e6ma I
CLEAR :ADD/DLT KEY I
Now, press AY to continue. SELECT:••KEY I
SET :< KEY l
Repeat step 5 untilthe Caption List END :ACTIONKEY )
is complete.
To Make Corrections
Press AV and • to selectthe memorizedchannelnumber.Then,
press &T to change,orADD/DLT to deletethe memorized
channelnumber.
6 Press ACTION four times to exit this mode and return
to the normal screen.
Manual Caption
a Follow steps 1-3 in the above section, d Press AV to select, [.... MANUALC_"T,ON.... I
and then press • to I cHNUMBERC_'noNI
b In step 4, press &V [--- CHAN,ELCAPT,ON--- / enter each character I _ a--- I
tOselect "MANUAL , of the caption. " I ;LF__:_O,DLTKEY I
I _ / SELECT:• • KEY I
CAPTION," and then • Characters will change in I sET :,qi. KEY I
" the following order. [ END :ACTIONKEY J
press • to display-- I SELECT:• • KEY ---_-A--*B_C ..... _.Z-_BLANK---_----=-&_
the MANUAL I sET :, KEY
•- CAPTION screen. I END :ACTIONKEY [ " 94 ..... 24-14--(pI-/4-!4_ /
C
I.... MANUAL CAPTION .... )
Press &_' to select CHN ER CAPTION
"CHNUMBER'"and] ;8 /
then press • to ....
move the shaded area I SELECT:•• KEY I
I sET :, KEY I
to the right side. !,END :ACTIONKEY J
• Channels already set in
_ the "Preset Caption" section are not displayed.
• You can set a total of ten channel captions with up to
four characters each.
Now, press • repeatedlyto move the cursorback
to=CHNUMBER."Repeat stepsc-d as desired.
To Make Corrections, repeatedlypress I_. to
movethecursortothe right,or • tomovetothe
lefttotheincorrect-entryand makethe correction.
To Clear the caption, pressADD/DLT.
e Press ACTION four times to exit this
mode and return to the normal screen.
20
To Next Page
Loading...
