Check the following points once again if you are having trouble with your VCR.
(BO : refers to =Basic Operations"Instructionbook.)
(AO : refers to =AdvancedOperations"Instructionbook.)
I:=*I,,Tz_ .J¢K_Z'_l[o]l
NO power._ Completely insert Power Plug into an AC outlet.
Set POWER button to on.
Make sure power source is active.
• =-i;_ele]|ell|i@E .- i d i_ | i e,r. t_I., . , .-J II |_t'lt [eJl
TV program cannot be recorded... • Check connections between VCR, external antenna, and
TV.
• Check connections selection. (BOp. 4, AO p. 3)
• Make sure your antenna system (CABLE or TV) is
correctly set. (ChanneLs [AO p. 12])
• Make sure cassette record tab is intact. (BO p. 3)
Timer recording cannot be • Confirm that clock is set to current time and date.
_en_ormed... • Make sure Cable/DSS box (if used) is left on and tuned to
channel to be recorded.
• Set recording start/stop times correctly. (BOp. 6)
• Make sure VCR POWER button is pressed off. (BOp. 6)
• Timer recording may not be pedormed or continued if a
power interruption occurs before or during a Timer
Recording, even after power is restored.
There is no playback picture, or the • Select channel 3 or 4 on TV to match VCR output channel
playback picture is noisy or contains (3 or 4) (BOp. 4) or select LINE.
streaks... • Set VCR/TV selector to "VCR."
• Adjust TRACKING control in either direction. (130 p. 3)
• Try Head Cleaning. (BOp. 3)
Special effects .playback, picture may
contain some vertical jitter when using • Set "rV's Vertical Hold Control to MANUAL, then adjust.
a TV with an Automatic Vertical Hold
Control...
VCR cannot be controlled... • Make sure VCR power is on.
m; t=]aa[•)i_Le,_J_i[_
VCR cannot be remote controlled...
ACTION and PROG buttonsdo not
respond...
IILTJ_h P.ImT_e]lF,
Programs cannot be viewed on TV...
• Check Remote battedes.
• Make sure VCR LOCK is set to off. (AO p. 10)
• Make sure Timer Record is not in progress.
• Make sure VCR power is on.
• Make sure Remote is in VCR mode.
• Aim Remote Control directly at remote sensor on VCR.
(BOp. 7)
• Avoid any object blocking signal path.
• Check Remote batteries. (BOp. 3)
• Make sure VCR LOCK Lsset to off. (AOp. 10)
• Exposing VCR remote sensor to direct fluorescent or
outdoor light may cause signal interference.
• Check connections between VCR, extamal antenna, and
TV.
• Press VCR button for VCR mode. (AO p. 2)
• Check Remote batteries. (BOp. 3)
_l]llil_llll Ill i
• Make sure TV power is on.
• Make sure "IV is set to output of VCR.
• Check connections between VCR, external antenna, and
TV.
• Set VCR/TV selector to =TV.* (BOp. 5)
• Make sure proper signal source is selected.
• Insert the cassette with window side up; record tab facing
you.
• Check if a tape is already in the unit.
• Completely insert power Plug into an AC outlet.
• Make sure cassette record tab is intact. (BOp. 3)
• To enable Quick play mechanism, the cylinder wifl rotate
for about 3 minutes. This reduces response time from
Stop to Play mode and from Play to Rewind Search
mode.
Video cassette cannot be inserted...
Video cassette cannot be removed...
Video cassette ejects when a
recording is started or the power is
turned off for timer recording...
In Stop mode, the motor (CYLINDER)
continues to rotate...
If you cannot resolve the problem, ilease cell the Customer Call Center for product
assistance at 1-800-211-PANA (7262).
To locate an authorized servlcenter, please call toll free 1-800-211-PANA (7262).
or send e-mall to : conaumerproducts@panssonlc.com
-8-
To Next Page
Loading...
