Panasonic PT-LB80 - Page 5

Display mode Display
resolution
(dots)
1
Scanning frequency
H
(kHz)
V
(kHz)
Dot clock
frequency
(MHz)
Picture
quality
2
Input terminal
720 x 480i
720 x 576i
720 x 480i
720 x 576i
720 x 483
720 x 576
1280 x 720
1280 x 720
1920 x 1080i
640 x 400
640 x 480
800 x 600
832 x 624
1024 x 768
1280 x 768
1280 x 800
1152 x 864
1152 x 870
1280 x 960
1280 x 1024
1400 x 1050
1440 x 900
1600 x 1200
1680 x 1050
1920 x 1200
15.7
15.6
15.7
15.6
31.5
31.3
45.0
37.5
33.8
28.1
31.5
37.9
31.5
35.0
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
39.6
48.4
56.5
60.0
68.7
39.6
47.8
41.3
49.1
49.7
64.0
67.5
76.7
68.7
60.0
64.0
80.0
91.1
64.0
65.1
55.9
75.0
65.3
74.6
59.9
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
70.1
85.1
59.9
66.7
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
74.6
50.1
60.0
70.1
75.0
85.0
49.9
59.9
50.0
60.2
59.8
71.2
74.9
85.0
75.1
60.0
60.0
75.0
85.0
60.0
59.9
59.9
60.0
60.0
59.9
–
–
13.5
13.5
27.0
27.0
74.3
74.3
74.3
74.3
25.2
31.5
25.2
30.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
57.3
51.9
65.0
75.0
78.8
94.5
65.3
79.5
68.0
69.1
83.5
94.2
108.0
121.5
100.0
108.0
108.0
135.0
157.5
108.0
122.4
106.5
162.0
146.3
193.3
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
AA
AA
AA
AA
AA
A
A
A
A
A
A
A
B
A
A
A
B
B
A
B
A
B
B
B
NTSC/NTSC4.43/PAL-M/PAL60
PAL/PAL-N/SECAM
525i (480i)
625i (576i)
525p (480p)
625p (576p)
750 (720)/60p
750 (720)/50p
1125 (1080)/60i
1125 (1080)/50i
VESA70
VESA85
VGA60
VGA65
VGA72
VGA75
VGA85
SVGA55
SVGA60
SVGA70
SVGA75
SVGA85
MAC16
XGA50
XGA60
XGA70
XGA75
XGA85
WXG
A768
WXGA800
MXGA70
MXGA75
MXGA85
MAC21
MSXGA60
SXGA60
SXGA75
SXGA85
SXGA60+
WXGA+
UXGA60
WSXGA+
WUXGA
VIDEO/S-VIDEO
COMPUTER (RGB/YP
BPR)
COMPUTER (RGB/YP
BPR)
3
COMPUTER (RGB/YPBPR)
COMPUTER (RGB only)
S PEC F ILE
PT-LB80
Portable LCD Projector
As of May 2008 < 5 >
Computer data compatibility
This projector accepts up to 91 kHz horizontal scanning frequency and 162 MHz dot clock.
NOTE: Pixel thinning is applied to signals that exceed a dot clock frequency of 100 MHz. The display resolution of this projector is 1,024 x 768
pixels. Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.
List of compatible signals
1. The “i” appearing after the resolution indicates an interlaced signal.
2. The following symbols are used to indicate picture quality.
AA Maximum picture quality can be obtained.
A Signals are converted by the image processing circuit before picture is projected.
B Signals are compressed by the image processing circuit before picture is projected.
3. When 750 (720)/60p or 750 (720)/50p signals are input to a computer input terminal, images are projected in the WIDE750 (720) format. Be sure
to run the auto setup function.