Panasonic SL-S230

Other
Play
Methods
|
The
letters
such
as
@
in
the
various
illustrations
refer
to
the
descriptions
in
the
“Location
of
Controls”
(see
page
2)
section.
Skip play
The disc plays from a selected through to the end, then
play stops automatically.
Preparation: Put unit in stop mode.
1 ;
NORMAL:
RESUME 1 17t RANDOM
©
2 Select the desired track.
*SKIP @ SEARCH
O E
3
O
Random play
1
NORMAL ____.
© RESUME 1 1 FANDOM:
—
2 e
Release
as
© RESUME 1 RANDOM
(oo LT
pa
For your reference: :
elt is also possible to press pp while the unit is in stop
Status to change the first track to be played. (All tracks
are played eventually, regardless of which is played
first.)
Program play is not possible in the random mode.
Resume play
This function allows you to listen from the beginning of
the track where play stopped because the unit was
powered off (or switched to stop status). It is useful
when listening to CDs in the car, etc.
ee, NORMAL
RESUME 4 1 1 RANDOM
© mM
q
© AESUME 4 1I RANDOM
ECIN KHG Soak viene
—
For your reference:
eif the RESUME, NORMAL, RANDOM (play mode se-
lector) slider is-put in the RESUME position, the all-
repeat function will be activated automatically as soon
as the unit is powered on.
elf power is cut off near the end of a track (power off
status), playback may resume from the beginning of
the next track.
elf the unit is powered off while a disc was playing and
then a new disc is inserted, play will begin from the
middle of the new disc because the unit remembers
the position where play stopped on the old disc.
Program play
Up to 24 tracks can be entered in the program.
Preparation: Put unit in stop mode.
(NORMAL
© RESUME 4 0 3 RANDOM
oo po
2 Select the desired track.
SKIP @ SEARCH
O (real
3 Register in sequence.
(The indication “M” and the programmed se-
quence appear on the display panel.)
MEMORY/
© oye
4 Repeat steps 2 and 3 to program all
the desired tracks.
O
@ To program the same track in the se-
quence more than once
After step 3, press MEMORY/RECALL the desired num-
ber of times.
E If“ f” is displayed
No more tracks may be added to the sequence.
E To confirm the contents of the pro-
grammed sequence i
Press MEMORY/RECALL while the.disc is playing. (The
number of the programmed tracks appear on the dis-
play in sequence.) fe
E To delete the entire programmed se-
quence
Press M, POWER OFF.
Repeat function
Press REPEAT while disc is playing or when unit is in
stop status. REPEAT
For your reference:
t REPEAT is pressed during program play, only the
tracks in the program are repeated.
(The indication “ALL” is not displayed.)
The setting is switched in the sequence indicated below
each time REPEAT is pressed.
1-track repeat (1 ©)
Sp track is repeated.
All-track repeat (ALL >)
or) the tracks on the disc are repeated.
Cancel
Changing the sound quality
XBS ON:
Select this setting to boast the low-range response.
ON TOF
Q
~_
OFF:
Select this setting to turn off the XBS function.
XBS
OND OFF:
O wo
Anti-Shock Function
Anti shock works by reading audio data and storing it in
memory (up to 10 seconds worth). The unit then fills in
interruptions caused by bumps and vibrations with data
from the memory. This unit also incorporates a powerful
anti-shock mechanism that prevents skipping caused
when play speed is changed by swinging of the unit.
1
ANTI-SHOCK
OMI OFF
© tm
t
M.RESERVE
indicator status
HUU
orf
eThe position of the ANTI-SHOCK slider can be
changed during play, but this may cause a slight inter-
ruption in the sound because the disc's rotation speed
changes.
During ANTI-SHOCK operation, the disc rotates at a
higher rate than usual in collecting extra audio data.
This may cause the batteries to run out faster and
could result in a slight increase in disc rotation noise.
a Stable Normal {plenty of data is stored)
Bumping stops Normal (data again starts to be stored)
Bumps continue repeatedly Sound is interrupted (data buffer empty)
Play status
(audio data status)
Using the unit with an audio system
The ANTI-SHOCK uses digital signal compression tech-
nology. It is recommended that the ANTI-SHOCK be
kept in the OFF position if the unit is connected to a
home audio system.