Panasonic TC-14Z99M User Manual

Power Source :
AC AUTO 110-240V, 50/60 Hz
Power Consumption :
56W
Aerial Impedance : 75Ω unbalanced
Coaxial type
Receiving System : 17 Systems
Receiving Channels :
VHF 1-11 PAL B (Australia & N.Zealand)
1-12 PAL/SECAM D
1-12 NTSC M JAPAN
2-12 PAL/SECAM B, G
2-13 NTSC M U.S.A.
UHF 21-69 PAL G I/SECAM B, G, K1
28-69 PAL G (Australia)
13-56 PAL D
13-52 NTSC M JAPAN
14-69 NTSC NTSC M U.S.A.
CATV S1-S41 (Hyper)
Intermediate Frequency :
Video 38.0 MHz
Sound 31.5 MHz (D, K, K1)
32 MHz (I)
32.5 MHz (B, G)
33.5 MHz (M)
© 2005 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and
distribution is a violation of law.
TC-14Z99M
GP31 Chassis
Colour 33.57 MHz (PAL)
33.6 MHz (SECAM)
33.75 MHz (SECAM)
34.42 MHz (NTSC)
Video / Terminals : AV1, 2
RAV In Video In 1 Vp-p 75Ω
Audio In Approx. 400mVrms
Monitor Out Video Out 1 Vp-p 75Ω
Audio Out Approx. 400mVrms
High Voltage : 23.5kV±1.5
at zero beam current
Picture Tube : 37GDC86XTC02
37cm (14 inches)
Measured diagonally,
90° deflection
Audio Output : 5W
Dimensions : Height:353mm
Width : 447 mm
Depth : 370 mm
Mass : 10 kg (Net Wt.)
Specifications are subject to change without notice.
Mass and dimensions shown are approximate.
Colour Television
Specifications
ORDER NO. PMI-T0705-01

Panasonic TC-14Z99M Specifications

General

Brand	Panasonic
Model	TC-14Z99M
Category	TV
Language	English

Summary

Specifications

Safety Precautions

1.1 General Guide Lines

General guidelines for servicing the hot chassis and high voltage circuits.

1.2 Leakage Current Cold Check

Procedure to measure leakage current with the receiver unplugged.

1.3 Leakage Current Hot Check

Procedure to measure leakage current with the receiver plugged in.

1.4 X-Radiation

Warning and precautions regarding potential X-radiation during service.

GP31 Chassis Block Diagram

Service Hints

2.1 Service Position for E-Board

Instructions on how to position the TV for servicing the E-board.

2.2 Factory Mode Adjustment

Steps to enter and navigate the factory mode for TV adjustments.

2.3 +B Voltage Adjustment

Procedure for adjusting the +B voltage to specified test points.

2.4 Heater Voltage Confirmation

Steps to confirm the heater voltage using a voltmeter.

2.5 RF AGC Adjustment

How to adjust the RF Automatic Gain Control for optimal signal reception.

2.6 NTSC Tint Colour Adjustment

Procedure for adjusting tint and colour settings for NTSC signals.

2.7 PAL Colour Output Level Adjustment

Steps to adjust colour output levels for PAL signals using test patterns.

2.8 CRT VRS Adjustment

Adjusting the Vertical Raster Size (VRS) for CRT display.

2.9 CRT Cut Off Adjustment

Procedure for adjusting the CRT cut-off point for proper display.

2.10 Purity and Convergen Adjustment

Steps for adjusting colour purity and convergence of the CRT.

2.11 White Balance Adjustment

Adjusting the white balance for accurate colour reproduction.

Conductor Views

Schematic Diagram

A Board

L Board

Parts Locations

Replacement Parts List

6.1 Replacement Parts List

Detailed list of replacement parts with part numbers and descriptions.