To Next PageTo Next Page
Need help?Do you have a question about the Panasonic TC-50PX24 and is the answer not in the manual?
General guidelines for conducting repairs and servicing of the equipment.
Techniques to reduce component damage caused by electrostatic discharge (ESD).
Information and considerations regarding the use of lead-free solder in manufacturing and repair.
Diagram illustrating the layout of the Printed Circuit Boards (PCBs) in the unit.
Details on applicable input signals for Component (Y, PB, PR) and HDMI interfaces.
Procedure for accessing the service mode using remote control key commands.
Procedure for copying and restoring TV settings using an SD card for board replacement or hotel setup.
Procedure for checking IIC bus line status using the self-check function.
Table correlating Power LED blinking patterns to specific unit abnormalities.
Troubleshooting steps for diagnosing the 'no power' condition based on LED status.
Diagnostic flowchart for troubleshooting the 'no picture' symptom.
Description and usage of the SC jig for identifying faulty SC, SU, or SD boards.
Step-by-step instructions for removing the rear cover of the unit.
Procedure for safely removing the AC inlet connector and component.
Instructions for removing the Power Supply Board (P-Board) from the unit.
Procedures for performing calibration and adjustments on the unit.
Procedure for selecting the Vsus voltage setting (LOW/HIGH) after panel replacement.
Overall block diagram illustrating the main functional sections of the TV.
Detailed block diagram, part 1 of 4, showing interconnected modules.
Important caution regarding the correct assembly and locking of flexible cables in connectors.
Diagram showing the first set of wiring connections within the unit.
Notes and symbols used in the schematic diagrams, including component definitions.
Schematic diagram for the A-Board, section 1 of 14.
Layout views of the K-Board and S-Board, showing component placement.
Component layout view of the A-Board, showing placement of electronic components.
Layout views of the C1-Board, showing component placement on both sides.
Mechanical parts list with exploded views for identifying and replacing physical components.
List of electrical components with part numbers, descriptions, and quantities for replacement.
General guidelines for conducting repairs and servicing of the equipment.
Techniques to reduce component damage caused by electrostatic discharge (ESD).
Information and considerations regarding the use of lead-free solder in manufacturing and repair.
Diagram illustrating the layout of the Printed Circuit Boards (PCBs) in the unit.
Details on applicable input signals for Component (Y, PB, PR) and HDMI interfaces.
Procedure for accessing the service mode using remote control key commands.
Procedure for copying and restoring TV settings using an SD card for board replacement or hotel setup.
Procedure for checking IIC bus line status using the self-check function.
Table correlating Power LED blinking patterns to specific unit abnormalities.
Troubleshooting steps for diagnosing the 'no power' condition based on LED status.
Diagnostic flowchart for troubleshooting the 'no picture' symptom.
Description and usage of the SC jig for identifying faulty SC, SU, or SD boards.
Step-by-step instructions for removing the rear cover of the unit.
Procedure for safely removing the AC inlet connector and component.
Instructions for removing the Power Supply Board (P-Board) from the unit.
Procedures for performing calibration and adjustments on the unit.
Procedure for selecting the Vsus voltage setting (LOW/HIGH) after panel replacement.
Overall block diagram illustrating the main functional sections of the TV.
Detailed block diagram, part 1 of 4, showing interconnected modules.
Important caution regarding the correct assembly and locking of flexible cables in connectors.
Diagram showing the first set of wiring connections within the unit.
Notes and symbols used in the schematic diagrams, including component definitions.
Schematic diagram for the A-Board, section 1 of 14.
Layout views of the K-Board and S-Board, showing component placement.
Component layout view of the A-Board, showing placement of electronic components.
Layout views of the C1-Board, showing component placement on both sides.
Mechanical parts list with exploded views for identifying and replacing physical components.
List of electrical components with part numbers, descriptions, and quantities for replacement.
General| Screen Size | 50 inches |
|---|---|
| Display Type | Plasma |
| Resolution | 1366 x 768 |
| HDMI Ports | 2 |
| Component Video Inputs | 2 |
| Composite Video Inputs | 1 |
| Aspect Ratio | 16:9 |
| S-Video Inputs | 1 |
| Refresh Rate | 600Hz |
| Inputs | HDMI, Component, Composite, S-Video |
