Panasonic TC-P42G10

(Continued)
Adj ustments/Configurations (alternatives)
Sets the mode to select the channel with Channel up/down button
(All/Favorite/Digital only/Analog only)
÷ Favorite: Only channels registered as FAVORITE (p, 20)
Selects the screen menu language (p, 16) [Language
Adjusts the clock (p. 18) [Clock
Sets channels (p. 50) [ANT/Cable setup
Selects the terminal and label of the external equipment (p. 53)
[Component l/Component 2/HDMI I/HDMI 2/HDMI 3/Video 1Nideo 2]
To prevent howling, stops output of audio specified in this menu, (p. 53) (On/Off)
Prevents "Image retention" with Wobbling. (Automatic/Periodic)
÷ Automatic: Shifts the display image automatically. [Pixel orbiter _1
÷ Periodic: Shiftsthe displayimageevery(1/2/3/4)minutesaccordinqtowhatwas setinthe "Time(minutes)"menu.
Sets the time for "Pixel orbiter-Periodic" setting. (1121314)
Change the brightness of the side bar (Off/Dark/Mid/Bright) (4:3 mode only) [4:3 side bars_i
÷ The recommended setting is "Bright" to prevent panel "Image retention". (p, 60)
Press "OK" to start "Scrolling" on the screen (p, 60) [Scrolling bar ]
Controls equipment connected to HDMI terminals (p. 40) (On/Off)
÷ "Powerofflink","Poweronlink","Stand-bypowersave","Autopowerstand-by"and"Defaultspeakers"cannotbeselectedif"Off"isset. [VIERALink _i
Sets "Power on link" of HDMI connection equipment (p. 40) (Yes/No)
Sets "Power off link" of HDMI connection equipment (p, 40) (Yes/No)
Set "Stand-by power save" of HDMI connection equipment. (p, 40) (No/Yes)
Set "Auto power stand-by" of HDMI connection equipment. (p, 40)
(NoNes (with reminder)/Yes (no reminder)
Selects the default speakers (p, 40) (TV/Theater)
Sets Network setting (p. 44)
Sets VIERA CAST setting (p. 46)
Network setting ]
[VIERA CAST setting ]
[Network cameras list ]Set Network Camera status. (Search/Registration/Connection/Deleting/Default setting etc,) (p, 30)
To conserve energy, the TV automatically turns off when NO SIGNAL and NO OPERATION is performed
for more than 10 minutes. (Enable/Disable)
Note
÷ Not in use when setting "Auto power on", "On/Off Timer", "Lock", "SD mode" or Digital channel,
÷ "No signal for 10 minutes was activated" will be displayed for about 10 seconds when the TV is turned
on for the first time after turning the power off by "No signal for 10 minutes".
÷ The on-screendisplay will flash 3, 2 and 1to indicatethe last three (3) remaining minutes prior tothe shut-off,
To conserve energy, the TV automatically turns off when no operation of remote or side panel key
continues for more than 3 hours, (Enable/Disable)
Note b activi,: f.or03hours ]
÷ Not in use when setting "Auto power on", "On/Off Timer" or PC input display,
÷ "No activity for 3 hours was activated" will be displayed for about 10 seconds when the TV is turned on .
for the first time after turning the power off by "No activity for 3 hours".
÷ The on-screendisplay will flash 3, 2 and 1to indicatethe last three (3) remaining minutes prior tothe shut-off,
Turns TV On automatically when the cable box or a connected device is turned On. (No/Yes)
TV AC cord must be plugged into this device. TV comes on every time the power is restored, [Autopower en_]
÷ The "Sleep" timer, "On / Off timer", and "First time setup" will not function if "Auto power on" is set. (p. 54)
Set "Movie", "Thumbnail" or "Slideshow" to play back SD cards automatically.
(Slideshow/Thumbnail/Movie/Set later/Off)
Displays TV version and software license.
Performing Reset will clear all items set with Setup, such as channel settings, (p. 50)
About ]
[Reset to defaults ]
@
,_'-F
_'_
-_r-
Adj ustments/Configurations (alternatives)
Sets the mode to select the channel with Channel up/down button (All/Favorite/Digital only/Analog only)
Sets favorite channels, (p. 20)
Changes the station identifier. (p. 51)
Checks the signal strength if interference or freezing occurs on a digital image. (p, 51)
37