Panasonic Viera TC-P50VT20

32
33
Viewing
Network Camera
Network camera setting
Before using a Network camera, you need to register the camera as shown below. You can also
set default camera or disconnect/delete the registered cameras.
■
Press to exit from
a menu screen
■
Press to return
to the previous
screen
Follow direction - in “Network settings” (p.46)
Select “Setup” and “Network cameras list”
Menu
Displays compatible network cameras that
have been connected and registered.
Network settings
VIERA CAST setting
Network cameras list
Software update
Mac address
Connection test
Network connection
Wireless network
IP address/DNS settings
Wireless (WiFi)
00-0b-97-7c-65-e9
-
select
next
If there is no registered camera
Select “Yes” to start search
Please refer to camera’s settings and enable its link
mode.
Start searching for network camera?
Yes No
select
next
Set Network camera setting
R G
B Y
Select
RETURN
OK
Network cameras list
Model Status Default
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
Camera name
BL-C210A ConnectedCamera 1
Find cameras Delete
Disconnect Default camera
select
Network camera setting operation
“Please refer to camera’s settings and enable its link mode. Start searching for network camera?”
“Yes” to start camera search.
Before you start to search for a camera, switch the camera to registration
mode. (For this operation, please refer to the operating manual for the
Network camera.)
Search condition also depends on “Network settings” (p.46-49).
“Remove camera information?”
“Yes” to delete camera information.
“Disconnect to camera?”
“Yes” to delete camera connection.
“Disconnected” will be displayed in “Status”.
“Set this camera as default camera?”
“Yes” to set to the default use.
Displayed “(Default)” next to camera name.
(Available only when reconnecting)
“Connect to Camera?
“Yes”: “Connect” will be displayed in “Status”.
(Attach up to 8 Network cameras simultaneously).
Network Camera
■
Press to exit from
a menu screen
■
Press to return
to the previous
screen
Preparations
Internet connections (p. 31)
Example of Network connection (p. 31)
Network settings (p. 46-49)
Before connecting the Network camera to the TV, please complete “IP setting” and run
“Connection test”(p. 46-49)
With all connected equipment turned on
Display “VIERA Link” menu
If there is no registered camera displayed, please set it in
Network Camera settings. (p. 33)
There is also an option to start with sensor detection.
Select “Network camera”
Network camera
TV
VIERA Link control
Speaker output
Record now
Stop recording
Back to TV
select
OK
View
Select OK
RETURN
R
4 cam / 8 cam
Camera name
Camera 1
Model
BL-C210A
Multi screen
(1/4)
4 split screen
select
OK to Single screen
Default camera setting (p. 33)
R
4 cam / 8 cam
Select OK
RETURN
1
-
9
Camera name
Camera 1
Model
BL-C210A
Multi screen
(1/9)
9 split screen
select
OK to Single screen
Preset position
Home position
1
-
9
0
Pan
Tilt
RETURN
Single screen
Camera name
Camera 1
Model
BL-C210A
Single screen
Preset position
Home position
1
-
9
0
Pan
Tilt
RETURN
Navigation area
Note
A number of VIERA-compatible network cameras can be found at the following sites:
http://www.panasonic.com/
http://panasonic.net/pcc/products/netwkcam/
For more details on setting and operation of the Network camera, please also read
the operating manuals for the Network camera.
You can operate the Network camera from the TV remote and also check the images from the Network
camera on your TV.
VIERA Link control only with the TV’s remote control (p. 45)
Basic operation for Network camera