Panasonic WH-MDC05F3E5 User Manual (English)

Other manuals for Panasonic WH-MDC05F3E5

Questions and Answers:

H
hhartAug 18, 2025
Why is my Panasonic WH-MDC05F3E5 hard to heat up?
- A
  anthonywilsonAug 18, 2025
  There are several reasons why your Panasonic Heatpump system may be struggling to heat up: * If the panel and floor are being heated simultaneously, the water temperature may decrease, reducing the system's heating ability. * In low outdoor air temperatures, the system may take longer to heat up. * A blocked discharge or intake inlet on the mono bloc unit, perhaps by snow, can hinder performance. * A low preset water outlet temperature can also extend the heating time.
S
Steven HallAug 20, 2025
Why doesn't my Panasonic Heatpump system heat up instantly?
- A
  Andrea MooreAug 20, 2025
  If your Panasonic Heatpump system starts operating with cold water, it will take some time to heat the water to the desired temperature.
J
Jason TaylorAug 23, 2025
Why does my Panasonic WH-MDC05F3E5 Heatpump system switch off?
- N
  Nancy ShawAug 23, 2025
  The system might be switching off due to its protection control. If the water inlet temperature falls below 10 °C, the compressor will stop, and the backup heater will activate.
G
gina71Aug 26, 2025
Why is the HEAT indicator blinking on the display of my Panasonic WH-MDC05F3E5?
- W
  Wayne TorresAug 26, 2025
  The blinking HEAT indicator on your Panasonic Heatpump system's display indicates that the system is performing a deice operation.
D
David GonzalesAug 27, 2025
Why is there a delay after restarting my Panasonic WH-MDC05F3E5 Heatpump system?
- L
  Linda DanielsAug 28, 2025
  The delay you're experiencing after restarting your Panasonic Heatpump system is a protection mechanism for the compressor.
X
xwilliamsAug 30, 2025
Why does steam come out of my Panasonic Heatpump system's mono bloc unit in heating mode?
- W
  Wendy HernandezAug 30, 2025
  The steam coming from the mono bloc unit during heating mode is due to defrost operation in the heat exchanger.
E
Edgar BuckleySep 1, 2025
Why does the backup heater on my Panasonic WH-MDC05F3E5 turn on automatically when it's disabled?
- D
  David OchoaSep 1, 2025
  The backup heater might be turning on automatically, even when disabled, due to the protection control of the unit's heat exchanger.
A
Amy FloresSep 3, 2025
Why does my Panasonic WH-MDC05F3E5 Heatpump system make a loud refrigerant noise for a few minutes?
- B
  bandersonSep 3, 2025
  The loud refrigerant noise is caused by protection control during deice operation when the outdoor ambient temperature is lower than -10°C.
U
utaylorSep 6, 2025
Why does my Panasonic WH-MDC05F3E5 Heatpump system mono bloc unit emit water or steam?
- S
  steve50Sep 6, 2025
  The emission of water or steam from the mono bloc unit is due to condensation or evaporation occurring in the pipes.
C
Chris AdamsSep 8, 2025
Why does my Panasonic Heatpump system start automatically when the timer is not set?
- D
  Don McconnellSep 8, 2025
  The system might be starting automatically because the sterilization timer has been set.

Panasonic WH-MDC05F3E5 Specifications

General

Type	Air-to-Water Heat Pump
Heating Capacity	5.00 kW
Coefficient of Performance (COP)	4.74
Refrigerant	R32
Energy Efficiency Class (Heating)	A+++
Cooling Capacity	4.5 kW
Power Supply	230V / 1Ph / 50Hz
Operating Temperature Range (Heating)	-20°C to +35°C
Noise Level (Outdoor Unit)	45 dB(A)

Related product manuals

Panasonic WH-MDC06G3E5

100 pages

Panasonic WH-MXC09G3E5

100 pages

Panasonic WH-MDC05F3E5 Service Manual

Other manuals for Panasonic WH-MDC05F3E5

Questions and Answers:

Panasonic WH-MDC05F3E5 Specifications

Related product manuals