EasyManua.ls Logo

Panasonic WH-MDC06G3E5 - User Manual

Panasonic WH-MDC06G3E5
100 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Português Nederlands Italiano Deutsch Español Français English
F570004
Operating Instructions
(Mono bloc)
Air-to-Water Heatpump
Operating Instructions
(Mono bloc) Air-to-Water Heatpump
2-15
Installation Instructions attached.
Mode d’emploi
Pompe à chaleur air-eau (Mono bloc)
16-29
Consignes d’installation jointes.
Instrucciones de funcionamiento
Bomba de calor de aire a agua (Mono bloc)
30-43
Instrucciones de instalación adjuntas.
Bedienungsanleitung
(Kompaktgerät) Luft/Wasser-Wärmepumpe
44-57
Installationsanleitung liegt bei.
Istruzioni operative
Pompa di calore Aria-acqua (Mono bloc)
58-71
Istruzioni per l’installazione allegate.
Gebruiksaanwijzing
(Mono bloc) Air-to-Water Warmtepomp
72-85
De instructies voor installatie zijn bijgevoegd.
Instruções de funcionamento
Bomba de Calor Ar-Água (Mono bloco)
86-99
Instruções de instalação anexadas.
Model No.
Mono bloc Unit
WH-MDC09G3E5
WH-MDC06G3E5

Table of Contents

Other manuals for Panasonic WH-MDC06G3E5

Preview: Service Manual
Service Manual2 pages

Questions and Answers

  • A
    Ariel GonzalezAug 18, 2025
    Why is my Panasonic WH-MDC06G3E5 hard to heat up?
    • C
      contrerasryanAug 19, 2025
      There are several reasons why your Panasonic Heatpump system may be struggling to heat up: * If the panel and floor are being heated simultaneously, the water temperature may decrease, reducing the system's heating ability. * In low outdoor air temperatures, the system may take longer to heat up. * A blocked discharge or intake inlet on the mono bloc unit, perhaps by snow, can hinder performance. * A low preset water outlet temperature can also extend the heating time.
  • S
    Steven GrahamAug 21, 2025
    Why doesn't my Panasonic WH-MDC06G3E5 Heatpump system heat up instantly?
    • D
      Donald SmallAug 21, 2025
      If your Panasonic Heatpump system starts operating with cold water, it will take some time to heat the water to the desired temperature.
  • N
    Nicole HarrisAug 23, 2025
    Why does my Panasonic WH-MDC06G3E5 switch off?
    • M
      mmcdonaldAug 23, 2025
      The system might be switching off due to its protection control. If the water inlet temperature falls below 10 °C, the compressor will stop, and the backup heater will activate.
  • J
    justin00Aug 26, 2025
    Why is the HEAT indicator blinking on the display of my Panasonic WH-MDC06G3E5 Heatpump system?
    • S
      Sandra HarmonAug 26, 2025
      The blinking HEAT indicator on your Panasonic Heatpump system's display indicates that the system is performing a deice operation.
  • J
    Jamie FernandezAug 28, 2025
    Why is there a delay after restarting my Panasonic WH-MDC06G3E5 Heatpump system?
    • F
      fergusonangelaAug 28, 2025
      The delay you're experiencing after restarting your Panasonic Heatpump system is a protection mechanism for the compressor.
  • K
    Kathleen ShortAug 30, 2025
    Why does steam come out of my Panasonic WH-MDC06G3E5's mono bloc unit in heating mode?
    • H
      Heather SosaAug 30, 2025
      The steam coming from the mono bloc unit during heating mode is due to defrost operation in the heat exchanger.
  • G
    Glenda WestSep 1, 2025
    Why does the backup heater on my Panasonic WH-MDC06G3E5 turn on automatically when it's disabled?
    • J
      johnsoncraigSep 1, 2025
      The backup heater might be turning on automatically, even when disabled, due to the protection control of the unit's heat exchanger.
  • J
    John WilliamsSep 4, 2025
    Why does my Panasonic Heatpump system make a loud refrigerant noise for a few minutes?
    • A
      Angela LopezSep 4, 2025
      The loud refrigerant noise is caused by protection control during deice operation when the outdoor ambient temperature is lower than -10°C.
  • J
    James RodriguezSep 6, 2025
    Why does my Panasonic WH-MDC06G3E5 mono bloc unit emit water or steam?
    • C
      Caitlyn ManningSep 6, 2025
      The emission of water or steam from the mono bloc unit is due to condensation or evaporation occurring in the pipes.
  • A
    apierceSep 8, 2025
    Why does my Panasonic WH-MDC06G3E5 start automatically when the timer is not set?
    • F
      Francisco WillisSep 8, 2025
      The system might be starting automatically because the sterilization timer has been set.

Panasonic WH-MDC06G3E5 Specifications

General IconGeneral
TypeAir to Water Heatpump
Heating Capacity6 kW
Energy Efficiency ClassA+++
RefrigerantR32
Power Supply230V, 50Hz
Coefficient of Performance (Heating)5.03 (at 7°C outdoor, 35°C water outlet)
Operating Temperature Range-20°C to +35°C (Heating)

Related product manuals