H
Henry HamiltonSep 13, 2025
Why is the Panasonic WH-UX12HE8 operation delayed after restarting?
- WWillie BergSep 13, 2025
The delay is a protection mechanism for the compressor.
To Next PageTo Next PageWhy is the Panasonic WH-UX12HE8 operation delayed after restarting?
The delay is a protection mechanism for the compressor.
Why does my Panasonic Air Conditioner outdoor unit emit water or steam?
The emission of water or steam from your Panasonic Air Conditioner's outdoor unit is due to condensation or evaporation occurring in the pipes.
Why is my Panasonic WH-UX12HE8 Heat Pump system hard to heat up?
Your Panasonic Heat Pump system may take longer to heat up if the panel and floor are heated simultaneously, which can decrease the warm water temperature and reduce heating ability. Also, low outdoor air temperature or a low preset water outlet temperature can extend the heating time. Check if the discharge outlet or intake inlet in the outdoor unit is blocked by obstacles like snow.
Why is there a water flowing sound in my Panasonic WH-UX12HE8?
The water flowing sound you hear during operation is due to the refrigerant flow inside the Panasonic Heat Pump unit.
What to do if operation in HEAT/COOL mode is not working efficiently in Panasonic Heat Pump?
If your Panasonic Heat Pump's HEAT/COOL mode isn't working efficiently, make sure the temperature is set correctly. Close the panel heater/cooler valve. Also, check the outdoor unit and clear any obstructions from the air inlet and outlet vents.
Why does Panasonic WH-UX12HE8 Heat Pump outdoor unit emits water or steam?
The water or steam emitted from the outdoor unit of your Panasonic Heat Pump is due to condensation or evaporation occurring in the pipes.
Why is my Panasonic Air Conditioner backup heater automatically turned ON when it is disabled?
If the backup heater in your Panasonic Air Conditioner turns on automatically when disabled, it's due to the protection control of the indoor unit heat exchanger.
Why does loud refrigerant noise continue for several minutes in my Panasonic Air Conditioner?
The loud refrigerant noise in your Panasonic Air Conditioner is caused by protection control during de-icing operation when the outdoor temperature is lower than -10 °C.
Why does my Panasonic Heat Pump start automatically?
Your Panasonic Heat Pump might be starting automatically because the sterilization timer has been set.
Why is my Panasonic Air Conditioner outdoor unit not operating?
The Panasonic Air Conditioner outdoor unit might not operate due to the system's protection control when the outdoor temperature is outside of the operating range.
General warnings and precautions for indoor and outdoor units.
Safety measures for power cords, including use of RCD/ELCB.
Identifies and explains the function of each button on the remote controller.
Selecting the number of zones and type of sensors used.
Connecting and configuring the buffer tank, including AT temperature settings.
Setting up an additional heat source (boiler) for backup heating.
Setting temperature thresholds and delay timers for activating the bivalent heat source.
Configuring bivalent heat for domestic hot water, including delay timers.
Setting up solar panel integration, including AT and antifreeze temperatures.
Controlling force heater operation and setting heating temperatures.
Setting water temperatures for heating using compensation curve or direct input.
Defining the outdoor temperature at which heating operation stops.
Setting the temperature difference (Delta T) for heating activation.
Setting water temperatures for cooling using compensation curve or direct input.
Explains normal sounds, heating delays, and slow heating issues.
Lists error codes displayed on the remote controller and their explanations.
General warnings and precautions for indoor and outdoor units.
Safety measures for power cords, including use of RCD/ELCB.
Identifies and explains the function of each button on the remote controller.
Selecting the number of zones and type of sensors used.
Connecting and configuring the buffer tank, including AT temperature settings.
Setting up an additional heat source (boiler) for backup heating.
Setting temperature thresholds and delay timers for activating the bivalent heat source.
Configuring bivalent heat for domestic hot water, including delay timers.
Setting up solar panel integration, including AT and antifreeze temperatures.
Controlling force heater operation and setting heating temperatures.
Setting water temperatures for heating using compensation curve or direct input.
Defining the outdoor temperature at which heating operation stops.
Setting the temperature difference (Delta T) for heating activation.
Setting water temperatures for cooling using compensation curve or direct input.
Explains normal sounds, heating delays, and slow heating issues.
Lists error codes displayed on the remote controller and their explanations.
General