Registering Headsets (G5 or XT-1)
Each headset must be registered to a basestation before it can be used.
Once registered, it should not need to be registered again unless it is
intentionally removed.
Add Headsets (G5 and/or XT-1)
Each headset has a unique identification number. The number is imprint- ed
on the headset and broadcast to the base station whenever it is turned on.
Note: A single headset should not be registered to more than one
basestation at any given site, whether or not the bases are interconnect-
ed. Remove the headset from the existing basestation before adding it to
a different one.
In dual-lane installations, all headsets are registered to Base #1. G5
shortcut: From the Main Menu, press the Left Arrow key to quickly access
the Add New Headsets registration function.
To register a headset:
1. Enter the base station configuration mode. G5: Select System Menu.
2. Select 04 Registraton > 1 Add New Headsets.
3. Power on the headset when prompted. Or in the case of a G5 headset,
insert the battery to automatically power on the headset.
4. Wait up to two minutes for {Headset xxxxxxx Has Been Registered!} to
appear at the bottom of the display.
5. Repeat step 3 for additional headsets.
6. Press Mode when finished.
Remove Headsets
Perform the following steps to un-register a lost, destroyed, or otherwise
removed headset from the system, including a headset that is sent back
to 3M for repair. The repaired headset would have to be registered again
at a later date.
1. Enter the base station configuration mode. G5: Select System Menu.
2. Select 04 Registration > 2 Remove Headsets.
3. Scroll to the number of the headset you want to un-register.
4. Press Enter.
Note: If you do not know or have access to the number of the headset to
be unregistered, identify the headsets that you want to remain in service
and un-register any that remain on the list.
List All Headsets
To see a list of the registered headsets:
1. Enter the base station configuration mode. G5: Select System Menu.
2. Select 04 Registration > 3 List All Headsets. Change Site Scheduling
The site schedule is the calendar of store open and closing times.
Note: All timekeeping is done using a 24 hour clock (e.g., 6:00 p.m.
appears as 18:00).
Regular Site Schedule:
The regular site schedule is the opening and closing times for each day of
the week and the times assigned as “Day” and “Night,” which determine
when the day and night volume settings change.
Perform the following procedure to set the regular site schedule:
1. Enter the basestation configuration mode. G5: Select System Menu.
2. Navigate to 10 Site Scheduling > Regular Site Schedule.
3. Change the value for each day of the week and each of the four defined
fields (Open, Day, Night, and Close). Press , , and to scroll up and down
the list.
Holiday/Exception Schedule:
The holiday/exception schedule can be used to identify up to 12 days in the year
on which the store schedule is different than it would have been otherwise.
The holiday/exception schedule should be updated at least once a year to
ensure it conforms to the current year’s calendar.
Perform the following procedure to set the holiday/exception schedule:
1. Enter the base station configuration mode. G5: Select System Menu.
2. Navigate to 10 Site Scheduling > Holiday/Exception Schedule.
3. For each day that needs a non-typical schedule, enter the three-letter
month and two digit date under Date, then change the open and close
times on the line to the right of the date. Press , , and to scroll through the
fields.
Store is Now Closed Message
Perform the following procedure to enable or disable the automatic store
closed prompt to let customers know in your absence that the store is closed.
Note: Make sure that you disable the automatic store closed prompt in stores
that are open 24 hours.
For Dual Lane operations, this option is only available under Lane 1
display screen.
1. Enter the base station configuration mode. G5: Select System Menu.
2. Change the value for 07 Global Settings > “Store is Now Closed” Prompt? to
Yes or No.
Reboot System
Perform the following procedure to cleanly power down, then power up without
unplugging the system:
1. Enter the configuration mode. G5: Select System Menu.
2. Select 17 Reboot System.
3. Change the value of Power Cycle Complete System to Yes.
4. G5: Press SERVICE. XT-1: Press ENTER.
This material has been created in order to accommodate a wide range of restaurant operations and your specific business practices and system configuration may differ slightly from what is represented in this material.
While ParTech, Inc. (“PAR”) takes great care to ensure the accuracy of these materials, all material is provided “as is” without warranty of any kind, either express or implied, including, but not limited to, warranties of
merchantability or fitness for a particular purpose. PAR does not make any warranties or representations that the materials will meet your requirements or that the operations of the hardware will be uninterrupted
error free.
Trademark Notices: The PAR logo is a trademarks of PAR Technology Corporation, the parent company of ParTech, Inc. or its affiliates. All other product names used throughout this material are trademarks of the
respective companies. No such use of any trademark is intended to convey endorsement or other affiliation with these companies.
Reproduction: Copyright © 2019, 2020 ParTech, Inc. All rights reserved. This publication, or any part thereof, may not be reproduced or transmitted in any form or by any means, electronic or mechanical,including
photocopying, recording, storage in an information retrieval system, or otherwise, without the prior written permission of
ParTech, Inc., PAR Technology Park, 8383 Seneca Turnpike, New Hartford, NY 13413-4991 USA. 78-8117-4871-0
To Previous Page
Loading...