Need help?Do you have a question about the Paso Sound Products DMS 3040-40 and is the answer not in the manual?
Comprehensive guide for installing and operating the DMS series integrated amplifiers.
Introduces the DMS series amplifiers and lists key features like channel count, zones, and model numbers.
Lists the primary characteristics and benefits of the amplifier's design, such as high performance and low distortion.
Provides a summary of the amplifier's technical capabilities, including frequency response, distortion, and power output.
Instructions for inspecting the unit upon receipt and handling potential shipping damage claims.
Essential warnings and instructions for safe use, covering water exposure, ventilation, and heat sources.
Specific instructions for securely mounting the amplifier in a rack system.
Detailed explanation of volume, tone, and power controls found on the front panel.
A comprehensive list and description of each numbered terminal and connector on the rear panel.
Illustrates the top-down view of the main printed circuit board and the Music on Hold board.
Lists default configurations for main PCB jumpers affecting inputs, VOX, and MUTE functions.
Details the default settings for switches located on the rear panel, such as Tone Bypass.
Describes how VOX and MUTE functions are managed through input sockets and internal jumpers.
Provides instructions on how to configure VOX and MUTE functions using jumpers for specific input behavior.
Demonstrates specific jumper settings for VOX and MUTE functions involving microphone and telephone inputs.
Shows example jumper settings for VOX and MUTE, including jukebox and music muting scenarios.
Detailed instructions and diagram for connecting a 3-wire balanced microphone to the amplifier.
Instructions and diagram for connecting a 2-wire unbalanced microphone, including cable length limitations.
Wiring instructions for connecting a desk base microphone, including the muting switch setup.
Details muting priority settings and how to mute the AUX 1 input during paging.
Guidance on configuring phantom power for microphone inputs using jumpers.
Wiring diagram and configuration tables for connecting balanced condenser and electret microphones.
Illustrates the connection of a telephone system's Key Service Unit (KSU) to the amplifier's TEL input.
Specific wiring diagram for connecting the telephone system's paging output to the amplifier.
Step-by-step guide to setting up the amplifier's Input 4 to function as an AUX 1 input.
Explanation of the AUX 1 sensitivity attenuator and how stereo signals are summed to mono.
Step-by-step guide to setting up the amplifier's Input 5 to function as an AUX 2 input.
Explanation of the AUX 2 sensitivity attenuator and how stereo signals are summed to mono.
Instructions on how to set the sensitivity levels for VOX 1 and VOX 2 to activate muting.
A table listing the default factory settings for VOX jumpers on various inputs.
How to perform direct muting by shorting mute terminals to ground.
A table listing the default factory settings for MUTE jumpers on various inputs.
Explains how to set MIC 1 to be muted by default and unmuted via a switch.
Diagram and jumper settings for implementing a 2-zone paging system with zone selection switches.
Explains how paging microphones and music sources are connected and operate within a 2-zone setup.
Guide on using the EQ Link feature to insert an external equalizer into the signal path.
Instructions on how to bridge two amplifiers using the Mix Buss to share inputs and outputs.
Details the installation and operation of the master remote volume control.
Instructions for installing and using a remote volume control for the Input 4 (AUX 1) channel.
Detailed steps for physically installing an audio module, including connector handling.
Illustrates the module connector's contacts and their functions, including power, input, and ground.
Details the default jumper and switch settings for module-specific VOX, MUTE, and input source selection.
Explains the 1 Watt, 8 Ohm outputs for Zone 1 and Zone 2, including level controls and input source selection.
Details the operation of the Music on Hold amplifier, its input sources, and how it interacts with paging and muting.
Illustrates the rear panel connections for the MOH system, including telephone input and zone outputs.
Guide on selecting the input source for the MOH and Zone 1 amplifier using jumpers.
Explains the functionality of the Zone 1 and Zone 2 outputs, including their independent operation and source selection.
Details how to select the input source for the Zone 1 and Zone 2 amplifiers using jumpers.
Diagram showing how to connect one 8-ohm speaker to each zone output.
Diagrams illustrating connections for two 4-ohm or two 8-ohm speakers per zone.
Diagram showing how to connect four 8-ohm speakers to each zone output.
Details the regulated 24V DC output for accessories and wire gauge considerations.
Explains how the VOX relay operates and can be configured to activate with VOX 1, VOX 2, or both.
Guide for using the Bose module to equalize only the music input signal.
Guide for using the Bose module to equalize all amplifier inputs via the EQ Link.
Illustrates a common wiring setup for restaurants, covering paging, music, and jukebox integration.
Wiring diagram and explanation for an auto service station installation, including ceiling speakers.
Wiring diagram and explanation for a retail store installation, covering music and paging systems.
Instructions on how to order replacement parts, including required information.
Details on how to obtain repair services, warranty claims, and proper packing procedures.
General| Brand | Paso Sound Products |
|---|---|
| Model | DMS 3040-40 |
| Category | Amplifier |
| Language | English |
To Next Page