Need help?Do you have a question about the PDi medTV16 and is the answer not in the manual?
General| Display Type | LED |
|---|---|
| Brightness | 250 cd/m² |
| Aspect Ratio | 16:9 |
| Speakers | 2 x 3W |
| VESA Mount | 75 x 75 mm |
| Built-in Speakers | Yes |
| Mount Type | VESA |
| Resolution | 1366 x 768 pixels |
| Inputs | HDMI, VGA, USB |
Do not expose the product to rain or moisture.
Ensure reliable operation and protect from overheating. Do not block openings.
Situate product away from heat sources like radiators or stoves.
Protect the power cord from being walked on or pinched.
Only use attachments and accessories specified by the manufacturer.
Unplug product during lightning storms to prevent damage.
Refer all servicing to qualified service personnel.
Do not use in an oxygen tent or chamber, may cause fire hazard.
Securely attach apparatus to wall to prevent injury from falling.
Operate only from indicated power source type.
Use only PDi power source for Power over Coax, ensure proper cable connection.
Requires solid copper center conductor and copper shield, max 150 ft.
Designed to attach to PDi suspension arm supporting seven pounds.
Safety brake pin must remain in place when removing TV or arm.
Three programmable levels (Free, Basic, Premium) and Disabled option.
Adjust brightness, contrast, color, tint, sharpness, and noise reduction.
Adjust picture settings like brightness, contrast, color, tint, and sharpness.
Adjust color balance with standard, reddish, greenish, or bluish options.
Enable or disable noise reduction for picture improvement.
Allows precise adjustment of sound parameters.
Adjust speaker volume balance from left to right.
Set the minimum volume level the TV can reach.
Set the maximum volume level the TV can reach.
Set the initial volume for the TV upon powering on.
Enable or disable internal speakers for each service level and source.
Adjust volume in 10 percent increments for TV input or HDMI.
Select Mono or Stereo sound mode for the earphone jack.
Set boost levels for analog pillow speakers.
Select signal type (Air, Cable STD, Cable IRC) for channel scanning.
Set the order in which channels are displayed after searching.
Scan available channels for activity and memorize them into the selected Service Level.
Assign sequential channel numbers to channels in the list.
Manually adjust individual channel settings like alias, label, and service level.
Empties a service level of all its programmed channels, leaving it blank.
Copies one service level's channels to another service level.
Block channels, TV shows, movies, and connected devices.
View and manage TV ratings for content filtering.
Selectively present movie content based on MPAA rating.
Provides definitions for TV rating categories like TV-Y, TV-Y7, TV-G.
Block auxiliary sources like external signal inputs.
Set the duration for which an enabled Parental Lock will be active.
Display a certain channel each time the TV is turned on.
Lock the currently viewed channel to prevent tuning to other channels.
Memorize caption setting upon powering TV off; powers on with last caption setting.
TV turns on and stays on when electrical power is applied; prevents turning off by buttons.
Automatically powers off after a period of viewer inactivity for energy savings.
Selectable codes for independent control of single TV in multi-TV rooms.
Display Teletext in addition to Captions; recommended Disabled for USA.
Customize closed captions on ATSC/QAM channels, including font and color settings.
Set time zone and daylight savings automatically from digital channel signal.
TV turns off upon reaching the highest numbered channel, used with pillow speakers.
Control access to external sources via remote buttons or pillow speakers.
Set the TV's aspect ratio (4:3, 16:9, etc.) upon powering on.
Enable or disable an analog pillow speaker control.
Enable or disable a custom splash screen uploaded via USB.
Select the language for on-screen displays (English, French, Spanish).
Preset the TV to power on to a selected source.
View readouts of TV's internal operation; items are read-only.
Restore the TV to its original factory default settings.
Controls power usage when TV is in 'Standby' or 'OFF' stage.
Copy settings, update firmware, or change splash screen via USB.
Contact PDi Communication Systems for support.
Toggle between MTI and SmartPort settings for third-party systems.
Manage system password, enable/disable protection, or change password.
Provides information regarding authorized servicing and warranty terms.
To Next Page
