Peavey SRC 421-16 - Page 7

AUX. BAL. OUT (62)
A balanced line otitpjt ccntainirig the AUX, output eignal. The signal
level at this q utp ut is control led by I he AUX rrasier level. un less th e
''AUX Line Input'switcNHQ jack has been actvated This balanced
Q utput may b a used to baJance other eig nale wh ich may be patched
in ^ the AUX. Line Input. (See AUX Line In, $1)
MASTER SECTION
MASTER AUX. IN (63)
An i n put lo the Master for patch i ng in si g nals from e rte^nal dev ices
such as effects processors cf aOding channels from a second
mixer.
MASTER OUTPUT (64)
Ths oulput is a "Mono' combination of the left and right program
material. The signal level at this oulput ts determined Dy the master
level oontrcl. May be used to drive external devices such as power
amps, graphic eoualiiers. effects processors, etc.
MASTER LINE IN (65)
A line level input to The Master I me amplifier for patching In&gnals
before the balanceo oulput. This input lack isswiiching and may b©
used for Tn Line' loop capability in cortjurtclion with master line
output Any external signal patched in ^ this point may utilize the
.Tester line dnvar stage and the XLR batancea oulput, NOTE: The
risenion of a 1/4' phone plug at this point removes the balanced
output capab'My from the master, via the switching jack.
MASTER BAL. OUT (66)
A balanced ime output containing the Master “mono’ output eign^.
The sig/Tal level at this output is determined by the master level
control, unless the 'MASTER Line Input’ switching jack has been
activated- This balanced output may be used to balance other
signals which may be patched in at the Master Lin© Input. (Sea
MASTER Line In, K)
SUBMASTER SECTION
SUBMASTER AUX. INPUTS (67)
Those inputs may be used to paten an external signal into any of tne
four submix buses Aix<. inputs are normally used forconnectng a
second mixer for additional chani*»el5.
SU6MASTER SEND 6 (66)
These sends provide outputs from all tour Submasiers to drive
ex'ernai devices such as etfecis proceseora, tape recorder inputs,
graphe equalizers, etc. The signs) level at the “Sub Sends* is
determined by the Submaaiersliders, 1 friruA. Submaslersendsare
normally used as The output for an independent effects loop on a
particular sub group, or to supply an unbalanced output To tape
deck inputs. (See SUB Returns, 6$-)
SUB. 4, 3, 2 and 1 RETURN (66)
The sub returns a re switching in puts and rout© signals patched mat
this point directly to the Submasler PAN controls. The sub returns
are normaliv used to corripiets :he effects patch loop for signal
p'oc esei ng of i no Mdu al S ubmasters, (See SU 8 S E N DS, 68.) NOTE:
The sub return patch point Is “after* the Suomaster slider and
'before" the Submaster pan contrcL
EFX. A SECTION
EPX.ASEND (70}
The output from file combinaiicn of EFX. A charmel SENDS and the
EFX, A MASTER Control. This effects send is ncmially i^ed to drive
external effects processors controlled by the A Bus, and is the
output ocfiion of the "A“ effects loop. (See EFX, A Return. 71.)
EPX. A RETURN (71)
A 81 gnal pate hed into the E^. A Return i np ut i s routed dire ctly to th e
EFX. A level control, compleling the "A* effects loop. (See EFX. A
Send 7D) file EFX. Return jack Is normally used for the output from
external effects devices controlled by the EFX. A bus. NOTE' The
E FX. jack 18 ewitc h rng and wh en a 1 /4' phen a plug is pate he d i n at
thie point, the internal reverb eyatem ia disabled
EFX. B SECTION
EFX. B SEND (72)
The output from the eombinaror of EFX B channel SEND and the
EFX. 6 MASTER Ccnlrol This effects send is normally used to drive
external effects processors controlled by the EFX. Bus, end is the
output portion of the *B* effects loop. (See EFX. B Return, 73.) When
e xte rnal effects devices are not em ployed. th e EFX. B Send may be
uaed as aeeparate recording mx, or to drive addtional power amp/
speaker combinationd.
EFX. D RETURN (73)
A signal pate hed i nte the EFX B Return i nput i s routed dire ctly to th e
EFX. B level cor\tfol. completing the "B* effects loop. (See EFX. 6
Sen d, 72.) The EFX. Ratu m jack i s normal ly used for the o utput from
external effects devices controlled by the EFX, B bus.
STEREO SECTION
STEREO OUT (74)
A stereo (L and R) output is forovidea fer driving externa) devices
such as stereo tape recorders, stereo equalizers, stereo power
ampiifiefs, etc. The signal level at the stereo out jack is determined
by the stereo cut level control. NOTE; Stereo 1/4* plugs used to
eccese the ST E REO 0 UT sign al sh ou id be wi red Tip.«left and R ing
» right.
PFL SECTION
PFL AUX. (75)
A etereo jack for patching two PFL buses together from mixer to
mixer. Tip « PFL Audio Signal Ring « PFL Switching Control Signal,
and grounding the sleeve actives the PFL System.
PHANTOM POWER SECTION
PHANTOM POWER ON/OFF (76)
This switch seiscte 43V DC phantom power for all channels. In the
'*Off" position, no phantom powering ia available on any channels.