Peavey SRC 421-16 - Aux. Section

MASTER PATCH
wksrrH
RkGWT
RIGHT SECTION
RIGHT AUX. IN (5i)
An input to the RIGHT MASTER for patching in signals ^rom external
devices such as effects processors, or adding channels from a
second mixer.
RIGHT OUTPUT (52)
An output from the RIGHT MASTER for patchir>g signals out to
external devices such as effects processors, graphic equalizers,
power amplifiers, etc.
RIGHT LINE IN (53)
A line level input lo the Right Line Amplifier for patching in signals
before the balanced output. This input jack isewitching and may be
used for "In Line’' loop capability in conjunction with the right lin©
output An extern al signaJ pate h ed i n at t hi s po ml may u li \\ze ih e rig ht
line driver stag© and the XLR balanced outt^ut NOTE: The insertion
of a 1/4* phone plug at this point removes the Palarxoed output
capability from the right main, via the switching jack.
RIGHT BALANCED OUT (54)
A balanced line output containing the RIGHT OUTPUT signal. The
signal level at this output i3 conirolled by the right master slider,
u niess th e 'Rig ht Li ne Inpu t* swi tching j ack has bee n activated. This
balanced output may be used to balance other signals which may
Pe patched In at the RIGHT LINE INPUT, (See Right Line In. 53.)
LEFT SECTION
LEFT AUX. IN (55)
An input to the LEFT MASTER for patching in signals from external
devices such as effects processors, or adding channels frorn a
second mixer
LEFT OUTPUT (55)
An output from the LEFT MASTER for patching signals outtoexternai
devices such as effects processors, graphic equalizers, power
amplllierg, etc.
LEFT LINE IN (57)
A lin© level input to the Lett Line Amplifier for patching in signals
be fore th e b alanced outp u t. Th is input jack is swi tc hm g and m ay be
used lor "In Line' loop capability in conjunction with the left line
output. An external signal patched in al this point may utilize the left
I i ne d n ver stag e and th e XLR bal a r^ced ou iput, NOT E; Th© m se rtion
of a 1/4* phone plug al this point r©moves ihe balanced output
capability from the left mam, via the switching jack.
LEFT BALANCED OUT (58)
A balanced line output containing the LEFT OUTPUT signal. The
sig n all eve I at th I s 0 uiput Is contra 11 ed by the I eft master s I ide r, u niess
the "Left Line Input" switching jack has been activaied. This bal¬
anced output may be used to balance other signals which may be
patched In at the LEFT LINE INPUT. (See Left Line In, 57.)
AUX. SECTION
AUX. AUX. IN (59)
An Input for patching ©xternaJ signals into the AUX mixing bus.
When conneciing more than one mixer for additional channels, The
AUX. orMonitor output from theseconO mixer should normally paich
in at this point
AUX. OUTPUT (60)
An output from the AUX, mixing bus for patching signals out to
external devices such as power amplifiers, graphic equalizers, etc.
The AUX. Output is normally used for a separate monitor mix. When
the channel's AUX. sends are operated m 'Pre’ position, the AUX.
Output is notalfected by channel EQ. The “POST* position allows
channel EO to become operational on AUX, output. (See AUX.
Control and Pre/Posi, 5.)
AUX. LINE IN (61)
A line level input to the AUX. Line Amplifier for patching in signals
before the balanced output. This input jack is switching and may be
used for "In Line' loop capability in conjunction with the AUX. line
output Any external signal patched in at this pDinimay utilize the
AUX. lin© driver stage and the XLR balanced output. NOTE' The
insertion of a 1/4* phone plug at this point removes the balanced
output capability from th© AUX. bus, via the switching jack.