Page 29
Addcamera
Refreshtheconnection
ActivatePIN/ Messageuponmotiondetection/Information
Note:
Notes:
Snapshot/Mute/manualrecord
!
!
!
!
!
!
!
!
!
!
!
#
#
!
!
!
!
!
!
!
!
!
Tap „AddCamera“ [26]to enroll anew camera, maximum6 camerasper
smartphone/tablet.Proceedasperchapter8.
Tap„Update“[28]torefreshthecameraconnection.
Tap„information“[29].
You can activate the PIN code access after turning on the smartphone /
tabletasfollows:
Tap„SetupPINLock“.
Enter the chosen PIN two times and a tick by “Enable lock when
starting”.
withoutthe valid PINit isnotpossible to connecttothe camera after
switching on your mobile device. Note your password and keep in a safe
place. If you forget the password the App must be deleted and then
reinstalledandtherequiredcamerassetupfresh.
In order to send a message through the App, to mobile devices which are
connected with the camera, upon motion detection add a tick against
„Notify Enable“ and confirm with “OK”. This is required for Android
devices.ForiOSthefunctionmustbesetasfollows:
StartthesettingontheHomesideofyouriOSdevice.
Select“Notifications”.
Scrolldowntothe“OMGuard”Appandselectthis.
Setthebuttonsto”ON”(functionactivated).
It can take up to 2 hours before this iOS function is activated by the
provider.
There may be a delay in receiving a message dependent on the
messagingserviceoftheprovider.
Tap „About“ to check information about the App. To close this side tap
„OK“.
Toreturntothemainsidetap„Information“[29]or„Close“.
Toview thelivecameraimagetapthestillimageonthemainside.Thelive
imageisshownin the lower half of the display.Toviewalargerimageturn
thedevice90°.
Toclosetheliveimagetapon„Back“[35].
Tomake a snapshotof theliveimage, tap „Snapshot“[32].The snapshot
willbestoredonthesmartphone/tablet.
To mute or reactivate thesound tap„Audio“ [33]. The sound will always
berecordedevenifthethesoundismuted.
Tomanually start a 2minuterecordingtap „record“ [34].The recordingis
storedonthemicroSDcardinthecamera.
Tap on „Operation“ [27] on the start side, to access the following
operationfunctions.
Retapon„Operation“toleavetheoperationside.
10.2 Liveimageside(seefig.E)
10.3 Operation(seefig.D)
SetEmailuponmotiondetection/Settings
Deletecamera
Viewanddeleterecordings(seefig.F)
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
#
Tap„Settings“[22]toselectthecamerasysteminformation(seefig.G).
Tick on „Enable Email Alert“ if an Email should be sent to the set Email
addressineventofmotiondetection(inserttickorpushbuttontotheright)
Tap„AdvancedSettings“toentertheSettingsside(seeChapter9).
Tosavethesettingstap„Save“[48]andconfirmwith„Yes“or„OK“.
To delete thecamera from theApp tap „DeleteCamera“ [23] andconfirm
with„Yes“.Itisnotnecessarytodeletethecamerainregularuse.
Tap on the event list [24] to view the recordings on the microSD card
.
To view further recordings tap [40] or „Search“, tap on the chosen time
frame.Confirmwith„Yes“forAndroiddevices.
Tap on the desired file to view the recording. If, due to poor connection,
thereis no imagethenwaitapprox.1 minuteandtrytoreplay the recoding
again.
To delete anindividual recording usingan Android deviceselect: “Delete”
[39]andtickagainsttherecording. Todelete all recordings tapthesymbol
with4squares. Afterselectingtap the bin symbol andconfirmwith “Yes”.
ForiOS select“DeleteAll”andcofirm with“Yes”,or“DeleteOne”andthen
tap the round red symbol in front of the recording and confirm with
“Delete”.
Toclosethelisttaponthebacksymbol.
Before fixing the camera permanently, test the quality of the connection
andoptimisethecameraview.
Thecameracanbewallorceilingmou
Firstlydisconnectallcables.
racket [9] ata suitable location
usingthescrews[19]andifnecessarythewallplugs[18]provided.
Screw the bracket into the appropiate threaded hole [13] in the camera
housing.
Adjust the angle of thecamera to give the required view and then tighten
thetriangularnut[7]andthewingscrew[8].
Screw the antenna [6] into the antenna connection [12] so that the
antennaisinanuprightposition.
If the connection to WiFi router is desired via network cable then connect
thecameratoviathelocalnetworkwiththenetworkplug[14].
Connect the mains adapter with a suitable mains outlet. The POWER LED
[3]lightsred.
Thecamerarunsamotion detection software which detects image changes and
automatically activates a recording and an alert message. This function
requiresthataformattedmicroSDcardisfitted.IfnomicroSDcardis fitted only
theAppconnectiontoliveimagesispossible.
Ifthe microSD card isfitted, thesoftwareisactive. When animage change
is detected, atwo minute recordingwith video andsound isautomatically
withinthelasthour
11. Installation
12. Motiondetectionrecordingandalert
nted(seefig.A:IandII).
For wall orceiling installation mountthe b
GB - 29
To Next Page
Loading...