PERFECTPRO SLIM-3 - Play Mode; Information Function; Aux in Mode; Setting the Clock

Theradiosupportsalimitednumberoffoldersandlesinthesearching:
Mode Max.no.offolderssupported Max.no.oflessupported
Stop 999(withfoldername) 9999(withlename)
Play 999 9999
  (1-99withfoldername) (1-999withlename)
  (100-999withoutfoldername) (1000-9999withoutlename)
Play mode
During USB memory device or SD card is playing,
1. Press the MENU button,
2. Rotate the TUNING/SEEK knob until the display shows “Play mode”. Press the
TUNING/SEEK knob.
3. Rotate the TUNING/SEEK knob to the desire play mode and press the TUNING/
SEEK knobtoconrm.
The radio will step through the following options:
Repeat 1
Repeat Folder Repeat All Random Normal Play
Repeat1 Repeatedlyplaytheleyouarelisteningto.
RepeatFolder Repeatedlyplaytheleswithinthefolderyouarelisteningto.
RepeatAll RepeatedlyplayalllesintheUSBmemorydeviceorSDcard.
Random PlayalllesintheUSBorSDcardonceinrandomorder.
The selected Play Mode is indicated on the right of the top line of the display by an icon.
No icon is shown when in Normal Play mode.
Information function
During USB memory device or SD card playback, press the INFO button to cycle
throughthefollowinginformation(onlyifthisinformationispresentwiththeleonthe
memory device):
File name (song) Folder name Artist name Album name Totalno.ofles
on the USB stick or SD card
Bit Rate Clock time and Date Normal playback
status (play time)
AUX IN MODE
A 3.5mm stereo Aux In socket is provided on the side behind the rubber cover, for
connecting an external audio device such as MP3 player or CD player (not included with
this radio).
1. Connect an audio SOURCE to the Aux In socket on the backside of the radio.
2. Press the SOURCE button to select AUX input. Display will show “AUX IN”.
3. Play the external player.
4. Adjust the volume of both the radio and the player for comfortable listening.
5. After use, close the rubber cover to prevent moist or dust from entering into the
sockets and radio.
Notes: Never use the AUX-IN socket in rainy or moist conditions to prevent moist from
entering the radio. Keep the rubber cover closed under these conditions.
The Auto-Power management function will be activated in AUX mode. If there is no
signal* from the AUX input jack for a period over 15 minutes, the unit will automatically
switch to standby mode. The operation indicator and the LCD will go off in such case.
Pressing the ON/OFF button will wake up the unit.
* Also when the incoming signal from the external device is too low and cannot be
detected for a period of over 15 minutes by the Auto-Power management, the radio will
switch to standby mode.
To prevent this raise the output level of the external device enough to be detected.
SETTING THE CLOCK
The clock can only be set when the radio is in standby mode. If no buttons are pressed
for 5 seconds, the radio will exit the clock setup and the setting is cancelled.
1. Press and hold the TUNING/SEEK knobfor12secondsuntilthehourdigitsash
on the display.
2. Rotate the TUNING/SEEK knob to set the hour.
3. Press the TUNING/SEEK knobtoconrm,theminutedigitsash.
4. Rotate the TUNING/SEEK knob to set the minute.
5. Press the TUNING/SEEK knobtoconrm,thedayashesonthedisplay.
6. Rotate the TUNING/SEEK knob to set the current day.
7. Press the TUNING/SEEK knobtoconrm,themonthashes.
8. Rotate the TUNING/SEEK knob to set the current month.
9. Press the TUNING/SEEK knobtoconrm,theyearwillthenashonthedisplay.
10. Rotate the TUNING/SEEK knob to set the current year.
11. Press the TUNING/SEEK knobtoconrm,“SYNCLOCKON”ashes.
12. Rotary the TUNING/SEEK knob to select “SYNCLOCK ON” or “SYNCLOCK OFF”.
13. Press the TUNING/SEEK knobtoconrmandnishtheclocksetting.
GB
2019